Post Stock Login Register

AISI 4140 vs EN 10028-2 10CrMo9-10

Minimal Match — 38% match based on chemical composition and mechanical property overlap.

AISI 4140 and EN 10028-2 10CrMo9-10 (EN 10028-2:2017) are both steel grades. Both fall under the Alloy Steel category. AISI 4140 is typically used for gears, shafts, dies, bolts, crankshafts, tooling, while EN 10028-2 10CrMo9-10 is commonly used for flat products for pressure purposes. AISI 4140 is defined under AISI, originating from United States, while EN 10028-2 10CrMo9-10 is defined under European Standard (EN), originating from Europe.

As per chemical composition, AISI 4140 vs EN 10028-2 10CrMo9-10 is a 57.1% match. As per mechanical properties, the match is 0%. Combined, this makes them a minimal match overall at 38%.

Frequently Compared With AISI 4140:
GOST 4543 12HN3A NF A35-565 100C6 UNI 11234 100Cr6 GB/T 3077 12Cr2Ni4A IS 4367 07Cr4Mo6 IS 1570 (Part 4) 105Cr5 IS 1570 (Part 4) 10Cr20Mo6 IS 1570 (Part 4) 07Cr4Mo6 IS 1570 (Part 4) 103Cr4 IS 1570 (Part 4) 103Cr6 IS 1570 (Part 7) 10Cr36Mo10H IS 4367 10Cr9Mo10
Match Breakdown
CHEMISTRY MATCH
57.1%
MECHANICAL MATCH
0%
OVERALL
38%
Specifications
Property AISI 4140 EN 10028-2 10CrMo9-10
Standard AISI EN 10028-2:2017
Category Alloy Steel Alloy Steel
C (%) 0.38–0.43 0.08-0.14
Mn (%) 0.75–1.00 0.40-0.80
Cr (%) 0.80–1.10 2.00-2.50
Mo (%) 0.15–0.25 0.90-1.10
Si (%) 0.15–0.35 <=0.50
S (%) ≤0.040 <=0.010
P (%) ≤0.035 <=0.020
N (%) Not specified <=0.012
Cu (%) Not specified <=0.30
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property AISI 4140 EN 10028-2 10CrMo9-10
Condition Quenched & Tempered Usual delivery condition normalized and tempered (+NT), nominal thickness up to 16 mm; transverse direction, Yield Strength is ReH, Elongation is A
Tensile Strength 850–1000 MPa 480-630 MPa
Yield Strength ≥680 MPa >=310 MPa
Elongation ≥13% >=18%
Hardness 248–302 HB Not specified
Impact (Charpy) ≥54 J Not specified
Typical Applications
AISI 4140
Gears, shafts, dies, bolts, crankshafts, tooling
EN 10028-2 10CrMo9-10
Flat products for pressure purposes
Key Differences
Can AISI 4140 Be Substituted With EN 10028-2 10CrMo9-10?
AISI 4140 and EN 10028-2 10CrMo9-10 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
Forms & Sizes Available on M-EX
AISI 4140
Round Bar → (3 listings)
Diameter: 50–50 mm (1.97–1.97 in)
Length: 5800–7000 mm (228.35–275.59 in)
EN 10028-2 10CrMo9-10
No active listings currently.
On M-EX Right Now
AISI 4140
3 active listings and RFQs →
EN 10028-2 10CrMo9-10
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between AISI 4140 and EN 10028-2 10CrMo9-10?
EN 10028-2 10CrMo9-10 specifies N, Cu which are not specified for AISI 4140.
Can AISI 4140 be substituted with EN 10028-2 10CrMo9-10?
AISI 4140 and EN 10028-2 10CrMo9-10 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.