Post Stock Login Register

ASTM A240/A240M N08332 vs EN 10088-1 1.4845

Minimal Match — 35% match based on chemical composition and mechanical property overlap.

ASTM A240/A240M N08332 (ASTM A240/A240M:2025) and EN 10088-1 1.4845 (EN 10088-1:2014) are both steel grades. Both fall under the Stainless Steel category. ASTM A240/A240M N08332 is typically used for pressure vessels and general applications (plate, sheet and strip), while EN 10088-1 1.4845 is commonly used for furnace parts, heat exchangers, kiln components. ASTM A240/A240M N08332 is defined under ASTM International, originating from United States, while EN 10088-1 1.4845 is defined under European Standard (EN), originating from Europe.

As per chemical composition, ASTM A240/A240M N08332 vs EN 10088-1 1.4845 is a 56.7% match. As per mechanical properties, the match is 0%. Combined, this makes them a minimal match overall at 35%.

Frequently Compared With ASTM A240/A240M N08332:
IS 1570 (Part 7) 12Cr12Ni2Mo ASTM A959 .- EN 10088-1 1.4006 EN 10088-1 1.4401 IS 1570 (Part 7) 12Cr12MoH GB/T 3280 06Cr19Ni10 GOST 5632 06Kh23N28 GOST 5632 08X18H10 IS 1570 (Part 7) 11Cr17Ni13W3TiH IS 1570 (Part 7) 12Cr12MoVH EN 10088-1 1.4301 IS 1570 (Part 7) 12Cr13H
Match Breakdown
CHEMISTRY MATCH
56.7%
MECHANICAL MATCH
0%
OVERALL
35%
Specifications
Property ASTM A240/A240M N08332 EN 10088-1 1.4845
Standard ASTM A240/A240M:2025 EN 10088-1:2014
Category Stainless Steel Stainless Steel
C (%) 0.05-0.10 ≤0.10
Mn (%) <=2.00 ≤2.00
P (%) <=0.030 Not specified
S (%) <=0.030 Not specified
Si (%) 0.75-1.50 ≤1.50
Cr (%) 17.0-20.0 24.0–26.0
Ni (%) 34.0-37.0 19.0–22.0
Cu (%) <=1.00 Not specified
Pb (%) <=0.005 Not specified
Sn (%) <=0.025 Not specified
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property ASTM A240/A240M N08332 EN 10088-1 1.4845
Tensile Strength >=462 MPa ≥515 MPa
Yield Strength >=186 MPa ≥205 MPa
Elongation >=30% ≥40%
Hardness <=88 HRBW Not specified
Condition Plate, sheet and strip; yield by 0.2 percent offset Not specified
Max Service Temp Not specified 1100°C continuous
Typical Applications
ASTM A240/A240M N08332
Pressure vessels and general applications (plate, sheet and strip)
EN 10088-1 1.4845
Furnace parts, heat exchangers, kiln components
Key Differences
Can ASTM A240/A240M N08332 Be Substituted With EN 10088-1 1.4845?
ASTM A240/A240M N08332 and EN 10088-1 1.4845 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
Forms & Sizes Available on M-EX
ASTM A240/A240M N08332
No active listings currently.
EN 10088-1 1.4845
Sheet → (3 listings)
Thickness: 6–6 mm (0.24–0.24 in)
Width: 1250–1250 mm (49.21–49.21 in)
Length: 2700–3200 mm (106.3–125.98 in)
On M-EX Right Now
ASTM A240/A240M N08332
0 active listings and RFQs →
EN 10088-1 1.4845
3 active listings and RFQs →
Frequently Asked Questions
What is the difference between ASTM A240/A240M N08332 and EN 10088-1 1.4845?
ASTM A240/A240M N08332 specifies P, S, Cu, Pb which are not specified for EN 10088-1 1.4845.
Can ASTM A240/A240M N08332 be substituted with EN 10088-1 1.4845?
ASTM A240/A240M N08332 and EN 10088-1 1.4845 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.