Post Stock Login Register

ASTM A240/A240M S31651 vs EN 10088-1 1.4845

Minimal Match — 35% match based on chemical composition and mechanical property overlap.

ASTM A240/A240M S31651 (ASTM A240/A240M:2025) and EN 10088-1 1.4845 (EN 10088-1:2014) are both steel grades. Both fall under the Stainless Steel category. ASTM A240/A240M S31651 is typically used for pressure vessels and general applications (plate, sheet and strip), while EN 10088-1 1.4845 is commonly used for furnace parts, heat exchangers, kiln components. ASTM A240/A240M S31651 is defined under ASTM International, originating from United States, while EN 10088-1 1.4845 is defined under European Standard (EN), originating from Europe.

As per chemical composition, ASTM A240/A240M S31651 vs EN 10088-1 1.4845 is a 54.3% match. As per mechanical properties, the match is 0%. Combined, this makes them a minimal match overall at 35%.

Frequently Compared With ASTM A240/A240M S31651:
EN 10088-1 1.4006 ASTM A959 .- GOST 5632 06Kh23N28 EN 10088-1 1.4401 IS 1570 (Part 7) 12Cr12MoH GOST 5632 08X18H10 EN 10088-1 1.4301 IS 1570 (Part 7) 12Cr12Ni2Mo GB/T 3280 06Cr19Ni10 IS 1570 (Part 7) 11Cr17Ni13W3TiH IS 1570 (Part 7) 12Cr12MoVH IS 1570 (Part 7) 12Cr13H
Match Breakdown
CHEMISTRY MATCH
54.3%
MECHANICAL MATCH
0%
OVERALL
35%
Specifications
Property ASTM A240/A240M S31651 EN 10088-1 1.4845
Standard ASTM A240/A240M:2025 EN 10088-1:2014
Category Stainless Steel Stainless Steel
C (%) <=0.08 ≤0.10
Mn (%) <=2.00 ≤2.00
P (%) <=0.045 Not specified
S (%) <=0.030 Not specified
Si (%) <=0.75 ≤1.50
Cr (%) 16.0-18.0 24.0–26.0
Ni (%) 10.0-14.0 19.0–22.0
Mo (%) 2.00-3.00 Not specified
N (%) 0.10-0.16 Not specified
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property ASTM A240/A240M S31651 EN 10088-1 1.4845
Tensile Strength >=550 MPa ≥515 MPa
Yield Strength >=240 MPa ≥205 MPa
Elongation >=35% ≥40%
Hardness <=217 HB Not specified
Condition Plate, sheet and strip; yield by 0.2 percent offset Not specified
Max Service Temp Not specified 1100°C continuous
Typical Applications
ASTM A240/A240M S31651
Pressure vessels and general applications (plate, sheet and strip)
EN 10088-1 1.4845
Furnace parts, heat exchangers, kiln components
Key Differences
Can ASTM A240/A240M S31651 Be Substituted With EN 10088-1 1.4845?
ASTM A240/A240M S31651 and EN 10088-1 1.4845 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
Forms & Sizes Available on M-EX
ASTM A240/A240M S31651
No active listings currently.
EN 10088-1 1.4845
Sheet → (3 listings)
Thickness: 6–6 mm (0.24–0.24 in)
Width: 1250–1250 mm (49.21–49.21 in)
Length: 2700–3200 mm (106.3–125.98 in)
On M-EX Right Now
ASTM A240/A240M S31651
0 active listings and RFQs →
EN 10088-1 1.4845
3 active listings and RFQs →
Frequently Asked Questions
What is the difference between ASTM A240/A240M S31651 and EN 10088-1 1.4845?
ASTM A240/A240M S31651 specifies P, S, Mo, N which are not specified for EN 10088-1 1.4845.
Can ASTM A240/A240M S31651 be substituted with EN 10088-1 1.4845?
ASTM A240/A240M S31651 and EN 10088-1 1.4845 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.