Post Stock Login Register

ASTM A240/A240M S31730 vs EN 10088-1 X2CrNiMo18-14-3

Close Alternative — 76.3% match based on chemical composition and mechanical property overlap.

ASTM A240/A240M S31730 (ASTM A240/A240M:2025) and EN 10088-1 X2CrNiMo18-14-3 (EN 10088-1:2023) are both steel grades. Both fall under the Stainless Steel category. ASTM A240/A240M S31730 is defined under ASTM International, originating from United States, while EN 10088-1 X2CrNiMo18-14-3 is defined under European Standard (EN), originating from Europe.

As per chemical composition, ASTM A240/A240M S31730 vs EN 10088-1 X2CrNiMo18-14-3 is a 76.3% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a close alternative overall at 76.3%.

Frequently Compared With ASTM A240/A240M S31730:
GOST 5632 06Kh23N28 IS 1570 (Part 7) 12Cr12MoVH ASTM A959 .- GB/T 3280 06Cr19Ni10 GOST 5632 08X18H10 EN 10088-1 1.4006 EN 10088-1 1.4301 EN 10088-1 1.4401 EN 10088-1 1.4845 IS 1570 (Part 7) 11Cr17Ni13W3TiH IS 1570 (Part 7) 12Cr12MoH IS 1570 (Part 7) 12Cr12Ni2Mo
Match Breakdown
CHEMISTRY MATCH
76.3%
MECHANICAL MATCH
No shared data
OVERALL
76.3%
Specifications
Property ASTM A240/A240M S31730 EN 10088-1 X2CrNiMo18-14-3
Standard ASTM A240/A240M:2025 EN 10088-1:2023
Category Stainless Steel Stainless Steel
C (%) <=0.030 <=0.030
Mn (%) <=2.00 <=2.00
P (%) <=0.040 <=0.045
S (%) <=0.010 <=0.015
Si (%) <=1.00 <=1.00
Cr (%) 17.0-19.0 17.0-19.0
Ni (%) 15.0-16.5 12.5-15.0
Mo (%) 3.0-4.0 2.50-3.00
N (%) <=0.045 <=0.10
Cu (%) 4.0-5.0 Not specified
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property ASTM A240/A240M S31730 EN 10088-1 X2CrNiMo18-14-3
Tensile Strength >=480 MPa Not specified
Yield Strength >=175 MPa Not specified
Elongation >=35% Not specified
Hardness <=90 HRBW Not specified
Condition Plate, sheet and strip; yield by 0.2 percent offset Not specified
Typical Applications
ASTM A240/A240M S31730
Pressure vessels and general applications (plate, sheet and strip)
EN 10088-1 X2CrNiMo18-14-3
Not documented
Key Differences
Can ASTM A240/A240M S31730 Be Substituted With EN 10088-1 X2CrNiMo18-14-3?
ASTM A240/A240M S31730 and EN 10088-1 X2CrNiMo18-14-3 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.
On M-EX Right Now
ASTM A240/A240M S31730
0 active listings and RFQs →
EN 10088-1 X2CrNiMo18-14-3
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between ASTM A240/A240M S31730 and EN 10088-1 X2CrNiMo18-14-3?
ASTM A240/A240M S31730 specifies Cu which is not specified for EN 10088-1 X2CrNiMo18-14-3.
Can ASTM A240/A240M S31730 be substituted with EN 10088-1 X2CrNiMo18-14-3?
ASTM A240/A240M S31730 and EN 10088-1 X2CrNiMo18-14-3 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.