Post Stock Login Register

ASTM A240/A240M S44735 vs ASTM A959 29-4

Close Alternative — 70.9% match based on chemical composition and mechanical property overlap.

ASTM A240/A240M S44735 (ASTM A240/A240M:2025) and ASTM A959 29-4 (ASTM A959:2011) are both steel grades. Both fall under the Stainless Steel category. ASTM A240/A240M S44735 is typically used for pressure vessels and general applications (plate, sheet and strip), while ASTM A959 29-4 is commonly used for wrought stainless steel products; recommended composition limits for adoption by product standards (clause 1.1). ASTM A240/A240M S44735 is defined under ASTM International, originating from United States, while ASTM A959 29-4 is defined under ASTM International, originating from United States.

As per chemical composition, ASTM A240/A240M S44735 vs ASTM A959 29-4 is a 70.9% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a close alternative overall at 70.9%.

Frequently Compared With ASTM A240/A240M S44735:
ASTM A959 29-4C GOST 5632 08X18H10 EN 10088-1 1.4006 EN 10088-1 1.4401 ASTM A959 26-3-3 ASTM A959 29-4-2 GB/T 3280 06Cr19Ni10 GOST 5632 06Kh23N28 EN 10088-1 1.4301 EN 10088-1 1.4845 IS 1570 (Part 7) 11Cr17Ni13W3TiH IS 1570 (Part 7) 12Cr12MoH
Match Breakdown
CHEMISTRY MATCH
70.9%
MECHANICAL MATCH
No shared data
OVERALL
70.9%
Specifications
Property ASTM A240/A240M S44735 ASTM A959 29-4
Standard ASTM A240/A240M:2025 ASTM A959:2011
Category Stainless Steel Stainless Steel
C (%) <=0.030 <=0.010
Mn (%) <=1.00 <=0.30
P (%) <=0.040 <=0.025
S (%) <=0.030 <=0.020
Si (%) <=1.00 <=0.20
Cr (%) 28.0-30.0 28.0-30.0
Ni (%) <=1.00 <=0.15
Mo (%) 3.6-4.2 3.5-4.2
N (%) <=0.045 <=0.020
Cu (%) Not specified <=0.15
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property ASTM A240/A240M S44735 ASTM A959 29-4
Tensile Strength >=550 MPa Not specified
Yield Strength >=415 MPa Not specified
Elongation >=18% Not specified
Hardness <=255 HB Not specified
Condition Plate, sheet and strip; yield by 0.2 percent offset Not specified
Typical Applications
ASTM A240/A240M S44735
Pressure vessels and general applications (plate, sheet and strip)
ASTM A959 29-4
Wrought stainless steel products; recommended composition limits for adoption by product standards (clause 1.1)
Key Differences
Can ASTM A240/A240M S44735 Be Substituted With ASTM A959 29-4?
ASTM A240/A240M S44735 and ASTM A959 29-4 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.
On M-EX Right Now
ASTM A240/A240M S44735
0 active listings and RFQs →
ASTM A959 29-4
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between ASTM A240/A240M S44735 and ASTM A959 29-4?
ASTM A959 29-4 specifies Cu which is not specified for ASTM A240/A240M S44735.
Can ASTM A240/A240M S44735 be substituted with ASTM A959 29-4?
ASTM A240/A240M S44735 and ASTM A959 29-4 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.