Post Stock Login Register

ASTM A516/A516M Grade 65 vs BS 970 (Part 1) 060A32

Close Alternative — 77.1% match based on chemical composition and mechanical property overlap.

ASTM A516/A516M Grade 65 (ASTM A516/A516M:2025) and BS 970 (Part 1) 060A32 (BS 970 (Part 1):1983) are both steel grades. Both fall under the Carbon Steel category. ASTM A516/A516M Grade 65 is typically used for welded pressure vessels where improved notch toughness is important, while BS 970 (Part 1) 060A32 is commonly used for through hardening steel for mechanical and allied engineering purposes; supplied in the hardened and tempered conditions of table 6.. ASTM A516/A516M Grade 65 is defined under ASTM International, originating from United States, while BS 970 (Part 1) 060A32 is defined under British Standards (BS), originating from United Kingdom.

As per chemical composition, ASTM A516/A516M Grade 65 vs BS 970 (Part 1) 060A32 is a 77.1% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a close alternative overall at 77.1%.

Frequently Compared With ASTM A516/A516M Grade 65:
BS 970 (Part 1) 045A10 BS 970 (Part 1) 045A10 BS 970 (Part 3) 045A10 BS 970 (Part 3) 070M20 BS 970 (Part 3) 080A15 BS 970 (Part 1) 040A04 BS 970 (Part 1) 040A10 BS 970 (Part 1) 040A12 BS 970 (Part 1) 045M10 BS 970 (Part 3) 045M10 BS 970 (Part 1) 045M10 BS 970 (Part 1) 055M15
Match Breakdown
CHEMISTRY MATCH
77.1%
MECHANICAL MATCH
No shared data
OVERALL
77.1%
Specifications
Property ASTM A516/A516M Grade 65 BS 970 (Part 1) 060A32
Standard ASTM A516/A516M:2025 BS 970 (Part 1):1983
Category Carbon Steel Carbon Steel
C (%) <=0.24 0.30-0.35
Mn (%) 0.85-1.20 0.50-0.70
P (%) <=0.025 <=0.050
S (%) <=0.025 <=0.050
Si (%) 0.15-0.40 Not specified
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property ASTM A516/A516M Grade 65 BS 970 (Part 1) 060A32
Tensile Strength 450-585 MPa Not specified
Yield Strength >=240 MPa Not specified
Elongation >=19% Not specified
Condition Tension test per Table 2; one set of values for all thicknesses; plates 40 mm and under normally as-rolled, over 40 mm normalized; Elongation is in 200 mm gauge length, 50 mm values in the tensile block Not specified
Typical Applications
ASTM A516/A516M Grade 65
Welded pressure vessels where improved notch toughness is important
BS 970 (Part 1) 060A32
Through hardening steel for mechanical and allied engineering purposes; supplied in the hardened and tempered conditions of Table 6.
Key Differences
Can ASTM A516/A516M Grade 65 Be Substituted With BS 970 (Part 1) 060A32?
ASTM A516/A516M Grade 65 and BS 970 (Part 1) 060A32 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.
On M-EX Right Now
ASTM A516/A516M Grade 65
0 active listings and RFQs →
BS 970 (Part 1) 060A32
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between ASTM A516/A516M Grade 65 and BS 970 (Part 1) 060A32?
ASTM A516/A516M Grade 65 specifies Si which is not specified for BS 970 (Part 1) 060A32.
Can ASTM A516/A516M Grade 65 be substituted with BS 970 (Part 1) 060A32?
ASTM A516/A516M Grade 65 and BS 970 (Part 1) 060A32 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.