Post Stock Login Register

ASTM A681 A5 vs EN ISO 4957 1.2316

Minimal Match — 35% match based on chemical composition and mechanical property overlap.

ASTM A681 A5 (ASTM A681:2008) and EN ISO 4957 1.2316 (EN ISO 4957:2018) are both steel grades. Both fall under the Tool & Die Steels category. ASTM A681 A5 is typically used for tools, dies and fixtures (clause 1.2), while EN ISO 4957 1.2316 is commonly used for plastic injection moulds for corrosive materials, food packaging moulds. ASTM A681 A5 is defined under ASTM International, originating from United States, while EN ISO 4957 1.2316 is defined under European Standard (EN), originating from Europe.

As per chemical composition, ASTM A681 A5 vs EN ISO 4957 1.2316 is a 60% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a minimal match overall at 35%.

Frequently Compared With ASTM A681 A5:
DIN EN ISO 4957 1.2344 DIN EN ISO 4957 1.2379 EN ISO 683-17 100Cr6 IS 1570 (Part 6) 103T3 IS 1570 (Part 6) 133T3 GOST 5950 3H2W8F GB/T 1299 4Cr5MoSiV GOST 5950 4H5MFS IS 1570 (Part 6) 118T3 GB/T 1299 4Cr5MoSiV1 GB/T 1299 3Cr2W8V IS 3748 103T3
Match Breakdown
CHEMISTRY MATCH
60%
MECHANICAL MATCH
No shared data
OVERALL
35%
Specifications
Property ASTM A681 A5 EN ISO 4957 1.2316
Standard ASTM A681:2008 EN ISO 4957:2018
Category Tool & Die Steels Tool & Die Steels
C (%) 0.95-1.05 ≤0.06
Mn (%) 2.80-3.20 ≤1.00
P (%) <=0.030 Not specified
S (%) <=0.030 Not specified
Si (%) 0.10-0.70 ≤0.50
Cr (%) 0.90-1.40 15.5–17.5
Mo (%) 0.90-1.40 0.80–1.30
Ni (%) Not specified 0.80–1.50
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property ASTM A681 A5 EN ISO 4957 1.2316
Hardness HRC Not specified 28–34 (pre-hardened)
Hardness HRC (hardened) Not specified 38–44
Corrosion Resistance Not specified Good in humid/corrosive environments
Typical Applications
ASTM A681 A5
Tools, dies and fixtures (clause 1.2)
EN ISO 4957 1.2316
Plastic injection moulds for corrosive materials, food packaging moulds
Key Differences
Can ASTM A681 A5 Be Substituted With EN ISO 4957 1.2316?
ASTM A681 A5 and EN ISO 4957 1.2316 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
Forms & Sizes Available on M-EX
ASTM A681 A5
No active listings currently.
EN ISO 4957 1.2316
Round Bar → (2 listings)
Diameter: 80–80 mm (3.15–3.15 in)
Length: 2600–2700 mm (102.36–106.3 in)
On M-EX Right Now
ASTM A681 A5
0 active listings and RFQs →
EN ISO 4957 1.2316
2 active listings and RFQs →
Frequently Asked Questions
What is the difference between ASTM A681 A5 and EN ISO 4957 1.2316?
ASTM A681 A5 specifies P, S which are not specified for EN ISO 4957 1.2316. EN ISO 4957 1.2316 specifies Ni which is not specified for ASTM A681 A5.
Can ASTM A681 A5 be substituted with EN ISO 4957 1.2316?
ASTM A681 A5 and EN ISO 4957 1.2316 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.