Post Stock Login Register

ASTM A959 201LN vs EN 10088-2 X2CrMnNiN17-7-5

Strong Match — 91.5% match based on chemical composition and mechanical property overlap.

ASTM A959 201LN (ASTM A959:2011) and EN 10088-2 X2CrMnNiN17-7-5 (EN 10088-2:2014) are both steel grades. Both fall under the Stainless Steel category. ASTM A959 201LN is typically used for wrought stainless steel products; recommended composition limits for adoption by product standards (clause 1.1), while EN 10088-2 X2CrMnNiN17-7-5 is commonly used for general purposes, hot or cold rolled sheet/plate and strip. ASTM A959 201LN is defined under ASTM International, originating from United States, while EN 10088-2 X2CrMnNiN17-7-5 is defined under European Standard (EN), originating from Europe.

As per chemical composition, ASTM A959 201LN vs EN 10088-2 X2CrMnNiN17-7-5 is a 91.5% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a strong match overall at 91.5%.

Frequently Compared With ASTM A959 201LN:
ASTM A959 .- ASTM A959 201L GB/T 3280 06Cr19Ni10 GOST 5632 06Kh23N28 GOST 5632 08X18H10 EN 10088-1 1.4006 EN 10088-1 1.4301 EN 10088-1 1.4401 IS 1570 (Part 7) 11Cr17Ni13W3TiH IS 1570 (Part 7) 12Cr12MoH IS 1570 (Part 7) 12Cr12MoVH EN 10088-1 1.4845
Match Breakdown
CHEMISTRY MATCH
91.5%
MECHANICAL MATCH
No shared data
OVERALL
91.5%
Specifications
Property ASTM A959 201LN EN 10088-2 X2CrMnNiN17-7-5
Standard ASTM A959:2011 EN 10088-2:2014
Category Stainless Steel Stainless Steel
C (%) <=0.03 <=0.030
Cr (%) 16.0-17.5 16.0-17.5
Cu (%) <=1.00 <=1.00
Mn (%) 6.4-7.5 6.0-8.0
N (%) 0.10-0.25 0.15-0.25
Ni (%) 4.0-5.0 3.5-5.5
P (%) <=0.045 <=0.045
S (%) <=0.015 <=0.015
Si (%) <=1.00 <=1.00
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property ASTM A959 201LN EN 10088-2 X2CrMnNiN17-7-5
Tensile Strength Not specified 650-850 MPa
Yield Strength Not specified >=300 MPa
Elongation Not specified >=45%
Condition Not specified Solution annealed (+AT), cold rolled strip, up to 8 mm thick; Yield Strength is Rp0.2 (transverse), Elongation is A80 for under 3 mm thick
Typical Applications
ASTM A959 201LN
Wrought stainless steel products; recommended composition limits for adoption by product standards (clause 1.1)
EN 10088-2 X2CrMnNiN17-7-5
General purposes, hot or cold rolled sheet/plate and strip
Can ASTM A959 201LN Be Substituted With EN 10088-2 X2CrMnNiN17-7-5?
ASTM A959 201LN and EN 10088-2 X2CrMnNiN17-7-5 overlap closely enough on chemistry and mechanical properties that EN 10088-2 X2CrMnNiN17-7-5 is often considered as a substitute for ASTM A959 201LN in many applications. Always confirm the specific property range your application needs before substituting, and check with your supplier's mill certificate.
On M-EX Right Now
ASTM A959 201LN
0 active listings and RFQs →
EN 10088-2 X2CrMnNiN17-7-5
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between ASTM A959 201LN and EN 10088-2 X2CrMnNiN17-7-5?
Both grades share a similar composition profile; see the specification table above for the exact chemistry and mechanical property values.
Can ASTM A959 201LN be substituted with EN 10088-2 X2CrMnNiN17-7-5?
ASTM A959 201LN and EN 10088-2 X2CrMnNiN17-7-5 overlap closely enough on chemistry and mechanical properties that EN 10088-2 X2CrMnNiN17-7-5 is often considered as a substitute for ASTM A959 201LN in many applications. Always confirm the specific property range your application needs before substituting, and check with your supplier's mill certificate.