Post Stock Login Register

ASTM A959 29-4C vs ASTM A276/A276M S44700

Close Alternative — 70.9% match based on chemical composition and mechanical property overlap.

ASTM A959 29-4C (ASTM A959:2011) and ASTM A276/A276M S44700 (ASTM A276/A276M:2017) are both steel grades. Both fall under the Stainless Steel category. ASTM A959 29-4C is typically used for wrought stainless steel products; recommended composition limits for adoption by product standards (clause 1.1), while ASTM A276/A276M S44700 is commonly used for stainless steel bars and shapes (hot-finished or cold-finished). ASTM A959 29-4C is defined under ASTM International, originating from United States, while ASTM A276/A276M S44700 is defined under ASTM International, originating from United States.

As per chemical composition, ASTM A959 29-4C vs ASTM A276/A276M S44700 is a 70.9% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a close alternative overall at 70.9%.

Frequently Compared With ASTM A959 29-4C:
ASTM A959 29-4-2 ASTM A959 26-3-3 ASTM A959 29-4 ASTM A959 25-4-4 GOST 5632 06Kh23N28 EN 10088-1 1.4401 GB/T 3280 06Cr19Ni10 EN 10088-1 1.4006 EN 10088-1 1.4301 ASTM A959 .- EN 10088-1 1.4845 IS 1570 (Part 7) 11Cr17Ni13W3TiH
Match Breakdown
CHEMISTRY MATCH
70.9%
MECHANICAL MATCH
No shared data
OVERALL
70.9%
Specifications
Property ASTM A959 29-4C ASTM A276/A276M S44700
Standard ASTM A959:2011 ASTM A276/A276M:2017
Category Stainless Steel Stainless Steel
C (%) <=0.030 <=0.010
Cr (%) 28.0-30.0 28.0-30.0
Mn (%) <=1.00 <=0.30
Mo (%) 3.6-4.2 3.5-4.2
N (%) <=0.045 <=0.020
Ni (%) <=1.00 <=0.15
P (%) <=0.040 <=0.025
S (%) <=0.030 <=0.020
Si (%) <=1.00 <=0.20
Cu (%) Not specified <=0.15
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property ASTM A959 29-4C ASTM A276/A276M S44700
Tensile Strength Not specified >=480 MPa
Yield Strength Not specified >=380 MPa
Elongation Not specified >=20%
Condition Not specified Condition A (Annealed), hot-finished, all sizes (first row printed)
Typical Applications
ASTM A959 29-4C
Wrought stainless steel products; recommended composition limits for adoption by product standards (clause 1.1)
ASTM A276/A276M S44700
Stainless steel bars and shapes (hot-finished or cold-finished)
Key Differences
Can ASTM A959 29-4C Be Substituted With ASTM A276/A276M S44700?
ASTM A959 29-4C and ASTM A276/A276M S44700 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.
On M-EX Right Now
ASTM A959 29-4C
0 active listings and RFQs →
ASTM A276/A276M S44700
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between ASTM A959 29-4C and ASTM A276/A276M S44700?
ASTM A276/A276M S44700 specifies Cu which is not specified for ASTM A959 29-4C.
Can ASTM A959 29-4C be substituted with ASTM A276/A276M S44700?
ASTM A959 29-4C and ASTM A276/A276M S44700 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.