Post Stock Login Register

ASTM A959 440FSe vs GOST 5632 12Kh13

Related Material — 69.9% match based on chemical composition and mechanical property overlap.

ASTM A959 440FSe (ASTM A959:2011) and GOST 5632 12Kh13 (GOST 5632-2014) are both steel grades. Both fall under the Stainless Steel category. ASTM A959 440FSe is typically used for wrought stainless steel products; recommended composition limits for adoption by product standards (clause 1.1), while GOST 5632 12Kh13 is commonly used for turbine blades, pump shafts, fasteners, cutlery. ASTM A959 440FSe is defined under ASTM International (United States).

As per chemical composition, ASTM A959 440FSe vs GOST 5632 12Kh13 is a 71.8% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a related material overall at 69.9%.

Frequently Compared With ASTM A959 440FSe:
IS 1570 (Part 7) 12Cr13H ASTM A959 .- GB/T 3280 06Cr19Ni10 GOST 5632 06Kh23N28 GOST 5632 08X18H10 EN 10088-1 1.4006 EN 10088-1 1.4401 EN 10088-1 1.4845 IS 1570 (Part 7) 12Cr12MoH IS 1570 (Part 7) 12Cr12MoVH IS 1570 (Part 7) 12Cr12Ni2Mo EN 10088-1 1.4301
Match Breakdown
CHEMISTRY MATCH
71.8%
MECHANICAL MATCH
No shared data
OVERALL
69.9%
Specifications
Property ASTM A959 440FSe GOST 5632 12Kh13
Standard ASTM A959:2011 GOST 5632-2014
Category Stainless Steel Stainless Steel
C (%) 0.95-1.20 0.09–0.15
Cr (%) 16.0-18.0 12.0–14.0
Mn (%) <=1.25 ≤0.80
P (%) <=0.06 Not specified
S (%) <=0.06 Not specified
Se (%) >=0.15 Not specified
Si (%) <=1.00 ≤0.80
Ni (%) Not specified ≤0.60
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property ASTM A959 440FSe GOST 5632 12Kh13
Tensile Strength Not specified ≥540 MPa (annealed)
Hardness HRC Not specified 36–45 (hardened)
Typical Applications
ASTM A959 440FSe
Wrought stainless steel products; recommended composition limits for adoption by product standards (clause 1.1)
GOST 5632 12Kh13
Turbine blades, pump shafts, fasteners, cutlery
Key Differences
Can ASTM A959 440FSe Be Substituted With GOST 5632 12Kh13?
ASTM A959 440FSe and GOST 5632 12Kh13 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
Forms & Sizes Available on M-EX
ASTM A959 440FSe
No active listings currently.
GOST 5632 12Kh13
Sheet → (2 listings)
Thickness: 6–6 mm (0.24–0.24 in)
Width: 1250–1250 mm (49.21–49.21 in)
Length: 2700–3400 mm (106.3–133.86 in)
On M-EX Right Now
ASTM A959 440FSe
0 active listings and RFQs →
GOST 5632 12Kh13
2 active listings and RFQs →
Frequently Asked Questions
What is the difference between ASTM A959 440FSe and GOST 5632 12Kh13?
ASTM A959 440FSe specifies P, S, Se which are not specified for GOST 5632 12Kh13. GOST 5632 12Kh13 specifies Ni which is not specified for ASTM A959 440FSe.
Can ASTM A959 440FSe be substituted with GOST 5632 12Kh13?
ASTM A959 440FSe and GOST 5632 12Kh13 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.