Post Stock Login Register

ASTM A959 S20162 vs EN 10088-3 X10CrNi18-8

Related Material — 67.1% match based on chemical composition and mechanical property overlap.

ASTM A959 S20162 (ASTM A959:2011) and EN 10088-3 X10CrNi18-8 (EN 10088-3:2014) are both steel grades. Both fall under the Stainless Steel category. ASTM A959 S20162 is typically used for wrought stainless steel products; recommended composition limits for adoption by product standards (clause 1.1), while EN 10088-3 X10CrNi18-8 is commonly used for general purposes, semi-finished products, bars, rods, wire, sections and bright products. ASTM A959 S20162 is defined under ASTM International, originating from United States, while EN 10088-3 X10CrNi18-8 is defined under European Standard (EN), originating from Europe.

As per chemical composition, ASTM A959 S20162 vs EN 10088-3 X10CrNi18-8 is a 67.1% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a related material overall at 67.1%.

Frequently Compared With ASTM A959 S20162:
EN 10088-1 1.4006 GB/T 3280 06Cr19Ni10 GOST 5632 06Kh23N28 GOST 5632 08X18H10 EN 10088-1 1.4845 IS 1570 (Part 7) 12Cr12Ni2Mo EN 10088-1 1.4301 EN 10088-1 1.4401 IS 1570 (Part 7) 11Cr17Ni13W3TiH IS 1570 (Part 7) 12Cr13H ASTM A959 .- IS 1570 (Part 7) 12Cr12MoH
Match Breakdown
CHEMISTRY MATCH
67.1%
MECHANICAL MATCH
No shared data
OVERALL
67.1%
Specifications
Property ASTM A959 S20162 EN 10088-3 X10CrNi18-8
Standard ASTM A959:2011 EN 10088-3:2014
Category Stainless Steel Stainless Steel
C (%) <=0.15 0.05-0.15
Cr (%) 16.5-21.0 16.0-19.0
Mn (%) 4.0-8.0 <=2.00
Mo (%) 0.50-2.50 <=0.80
N (%) 0.05-0.25 <=0.10
Ni (%) 6.0-10.0 6.0-9.5
P (%) <=0.040 <=0.045
S (%) <=0.040 <=0.015
Si (%) 2.5-4.5 <=2.00
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property ASTM A959 S20162 EN 10088-3 X10CrNi18-8
Tensile Strength Not specified 500-750 MPa
Yield Strength Not specified >=195 MPa
Elongation Not specified >=40%
Hardness Not specified <=230 HB
Condition Not specified Solution annealed (+AT), conditions 1C, 1E, 1D, 1X, 1G and 2D, thickness or diameter up to 40 mm; Yield Strength is Rp0.2, Elongation is A (longitudinal), hardness for guidance only
Typical Applications
ASTM A959 S20162
Wrought stainless steel products; recommended composition limits for adoption by product standards (clause 1.1)
EN 10088-3 X10CrNi18-8
General purposes, semi-finished products, bars, rods, wire, sections and bright products
Can ASTM A959 S20162 Be Substituted With EN 10088-3 X10CrNi18-8?
ASTM A959 S20162 and EN 10088-3 X10CrNi18-8 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
On M-EX Right Now
ASTM A959 S20162
0 active listings and RFQs →
EN 10088-3 X10CrNi18-8
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between ASTM A959 S20162 and EN 10088-3 X10CrNi18-8?
Both grades share a similar composition profile; see the specification table above for the exact chemistry and mechanical property values.
Can ASTM A959 S20162 be substituted with EN 10088-3 X10CrNi18-8?
ASTM A959 S20162 and EN 10088-3 X10CrNi18-8 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.