Post Stock Login Register

ASTM A959 S32053 vs ASTM A240/A240M N08932

Close Alternative — 72.6% match based on chemical composition and mechanical property overlap.

ASTM A959 S32053 (ASTM A959:2011) and ASTM A240/A240M N08932 (ASTM A240/A240M:2025) are both steel grades. Both fall under the Stainless Steel category. ASTM A959 S32053 is typically used for wrought stainless steel products; recommended composition limits for adoption by product standards (clause 1.1), while ASTM A240/A240M N08932 is commonly used for pressure vessels and general applications (plate, sheet and strip). ASTM A959 S32053 is defined under ASTM International, originating from United States, while ASTM A240/A240M N08932 is defined under ASTM International, originating from United States.

As per chemical composition, ASTM A959 S32053 vs ASTM A240/A240M N08932 is a 72.6% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a close alternative overall at 72.6%.

Frequently Compared With ASTM A959 S32053:
ASTM A959 2205 EN 10088-1 1.4006 IS 1570 (Part 7) 12Cr12MoVH GOST 5632 06Kh23N28 GOST 5632 08X18H10 EN 10088-1 1.4301 EN 10088-1 1.4845 IS 1570 (Part 7) 11Cr17Ni13W3TiH ASTM A959 .- GB/T 3280 06Cr19Ni10 EN 10088-1 1.4401 IS 1570 (Part 7) 12Cr12MoH
Match Breakdown
CHEMISTRY MATCH
72.6%
MECHANICAL MATCH
No shared data
OVERALL
72.6%
Specifications
Property ASTM A959 S32053 ASTM A240/A240M N08932
Standard ASTM A959:2011 ASTM A240/A240M:2025
Category Stainless Steel Stainless Steel
C (%) <=0.030 <=0.020
Cr (%) 22.0-24.0 24.0-26.0
Mn (%) <=1.00 <=2.00
Mo (%) 5.0-6.0 4.5-6.5
N (%) 0.17-0.22 0.15-0.25
Ni (%) 24.0-26.0 24.0-26.0
P (%) <=0.030 <=0.025
S (%) <=0.010 <=0.010
Si (%) <=1.00 <=0.40
Cu (%) Not specified 1.0-2.0
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property ASTM A959 S32053 ASTM A240/A240M N08932
Tensile Strength Not specified >=600 MPa
Yield Strength Not specified >=305 MPa
Elongation Not specified >=40%
Condition Not specified Plate, sheet and strip; yield by 0.2 percent offset
Typical Applications
ASTM A959 S32053
Wrought stainless steel products; recommended composition limits for adoption by product standards (clause 1.1)
ASTM A240/A240M N08932
Pressure vessels and general applications (plate, sheet and strip)
Key Differences
Can ASTM A959 S32053 Be Substituted With ASTM A240/A240M N08932?
ASTM A959 S32053 and ASTM A240/A240M N08932 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.
On M-EX Right Now
ASTM A959 S32053
0 active listings and RFQs →
ASTM A240/A240M N08932
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between ASTM A959 S32053 and ASTM A240/A240M N08932?
ASTM A240/A240M N08932 specifies Cu which is not specified for ASTM A959 S32053.
Can ASTM A959 S32053 be substituted with ASTM A240/A240M N08932?
ASTM A959 S32053 and ASTM A240/A240M N08932 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.