Post Stock Login Register

BS 970 (Part 1) 416S41 vs EN 10088-1 1.4006

Minimal Match — 35% match based on chemical composition and mechanical property overlap.

BS 970 (Part 1) 416S41 (BS 970 (Part 1):1983) and EN 10088-1 1.4006 (EN 10088-1:2014) are both steel grades. Both fall under the Stainless Steel category. BS 970 (Part 1) 416S41 is typically used for stainless and heat resisting steel for mechanical and allied engineering purposes (table 13)., while EN 10088-1 1.4006 is commonly used for cutlery, turbine blades, fasteners, surgical instruments. BS 970 (Part 1) 416S41 is defined under British Standards (BS), originating from United Kingdom, while EN 10088-1 1.4006 is defined under European Standard (EN), originating from Europe.

As per chemical composition, BS 970 (Part 1) 416S41 vs EN 10088-1 1.4006 is a 71.7% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a minimal match overall at 35%.

Frequently Compared With BS 970 (Part 1) 416S41:
IS 1570 (Part 7) 12Cr12MoH IS 1570 (Part 7) 12Cr12MoVH EN 10088-1 1.4845 IS 1570 (Part 7) 12Cr13H GOST 5632 08X18H10 EN 10088-1 1.4401 IS 1570 (Part 7) 12Cr12Ni2Mo GB/T 3280 06Cr19Ni10 GOST 5632 06Kh23N28 EN 10088-1 1.4301 ASTM A959 .- IS 1570 (Part 7) 11Cr17Ni13W3TiH
Match Breakdown
CHEMISTRY MATCH
71.7%
MECHANICAL MATCH
No shared data
OVERALL
35%
Specifications
Property BS 970 (Part 1) 416S41 EN 10088-1 1.4006
Standard BS 970 (Part 1):1983 EN 10088-1:2014
Category Stainless Steel Stainless Steel
C (%) 0.09-0.15 0.08–0.15
Si (%) <=1.0 ≤1.00
Mn (%) <=1.5 ≤1.50
P (%) <=0.060 Not specified
S (%) <=0.060 Not specified
Cr (%) 11.5-13.5 11.5–13.5
Mo (%) <=0.60 Not specified
Ni (%) <=1.00 ≤0.75
Se (%) 0.15-0.35 Not specified
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property BS 970 (Part 1) 416S41 EN 10088-1 1.4006
Tensile Strength Not specified ≥540 MPa (annealed)
Hardness HRC Not specified 36–45 (hardened)
Elongation Not specified ≥18%
Typical Applications
BS 970 (Part 1) 416S41
Stainless and heat resisting steel for mechanical and allied engineering purposes (Table 13).
EN 10088-1 1.4006
Cutlery, turbine blades, fasteners, surgical instruments
Key Differences
Can BS 970 (Part 1) 416S41 Be Substituted With EN 10088-1 1.4006?
BS 970 (Part 1) 416S41 and EN 10088-1 1.4006 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
Forms & Sizes Available on M-EX
BS 970 (Part 1) 416S41
No active listings currently.
EN 10088-1 1.4006
Sheet → (3 listings)
Thickness: 6–6 mm (0.24–0.24 in)
Width: 1250–1250 mm (49.21–49.21 in)
Length: 2700–3400 mm (106.3–133.86 in)
On M-EX Right Now
BS 970 (Part 1) 416S41
0 active listings and RFQs →
EN 10088-1 1.4006
3 active listings and RFQs →
Frequently Asked Questions
What is the difference between BS 970 (Part 1) 416S41 and EN 10088-1 1.4006?
BS 970 (Part 1) 416S41 specifies P, S, Mo, Se which are not specified for EN 10088-1 1.4006.
Can BS 970 (Part 1) 416S41 be substituted with EN 10088-1 1.4006?
BS 970 (Part 1) 416S41 and EN 10088-1 1.4006 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.