Post Stock Login Register

BS 970 (Part 1) 060A62 vs IS 1570 (Part 2/Sec 1) 60C4

Strong Match — 91.4% match based on chemical composition and mechanical property overlap.

BS 970 (Part 1) 060A62 (BS 970 (Part 1):1991) and IS 1570 (Part 2/Sec 1) 60C4 (IS 1570 (Part 2/Sec 1):1979) are both steel grades. Both fall under the Carbon Steel category. BS 970 (Part 1) 060A62 is typically used for as-rolled, or as-rolled and softened, steel (section two), while IS 1570 (Part 2/Sec 1) 60C4 is commonly used for springs, blades, high-strength wires, wear-resistant tools, hand tools. BS 970 (Part 1) 060A62 is defined under British Standards (BS), originating from United Kingdom, while IS 1570 (Part 2/Sec 1) 60C4 is defined under Bureau of Indian Standards (IS), originating from India.

As per chemical composition, BS 970 (Part 1) 060A62 vs IS 1570 (Part 2/Sec 1) 60C4 is a 91.4% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a strong match overall at 91.4%.

Frequently Compared With BS 970 (Part 1) 060A62:
BS 970 (Part 1) 040A12 BS 970 (Part 1) 045A10 BS 970 (Part 1) 060A81 BS 970 (Part 1) 040A10 BS 970 (Part 1) 060A72 BS 970 (Part 1) 080A15 BS 970 (Part 1) 060A78 BS 970 (Part 1) 070A67 BS 970 (Part 3) 070M20 BS 970 (Part 1) 040A04 BS 970 (Part 1) 060A67 BS 970 (Part 3) 080A15
Match Breakdown
CHEMISTRY MATCH
91.4%
MECHANICAL MATCH
No shared data
OVERALL
91.4%
Specifications
Property BS 970 (Part 1) 060A62 IS 1570 (Part 2/Sec 1) 60C4
Standard BS 970 (Part 1):1991 IS 1570 (Part 2/Sec 1):1979
Category Carbon Steel Carbon Steel
C (%) 0.60-0.65 0.55-0.65
Mn (%) 0.50-0.70 0.30-0.60
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property BS 970 (Part 1) 060A62 IS 1570 (Part 2/Sec 1) 60C4
Tensile Strength Not specified >=750 MPa
Elongation Not specified >=11%
Typical Applications
BS 970 (Part 1) 060A62
As-rolled, or as-rolled and softened, steel (section two)
IS 1570 (Part 2/Sec 1) 60C4
springs, blades, high-strength wires, wear-resistant tools, hand tools
Can BS 970 (Part 1) 060A62 Be Substituted With IS 1570 (Part 2/Sec 1) 60C4?
BS 970 (Part 1) 060A62 and IS 1570 (Part 2/Sec 1) 60C4 overlap closely enough on chemistry and mechanical properties that IS 1570 (Part 2/Sec 1) 60C4 is often considered as a substitute for BS 970 (Part 1) 060A62 in many applications. Always confirm the specific property range your application needs before substituting, and check with your supplier's mill certificate.
Forms & Sizes Available on M-EX
BS 970 (Part 1) 060A62
No active listings currently.
IS 1570 (Part 2/Sec 1) 60C4
Round Bar → (2 listings)
Diameter: 40–40 mm (1.57–1.57 in)
Length: 6000–6300 mm (236.22–248.03 in)
On M-EX Right Now
BS 970 (Part 1) 060A62
0 active listings and RFQs →
IS 1570 (Part 2/Sec 1) 60C4
2 active listings and RFQs →
Frequently Asked Questions
What is the difference between BS 970 (Part 1) 060A62 and IS 1570 (Part 2/Sec 1) 60C4?
Both grades share a similar composition profile; see the specification table above for the exact chemistry and mechanical property values.
Can BS 970 (Part 1) 060A62 be substituted with IS 1570 (Part 2/Sec 1) 60C4?
BS 970 (Part 1) 060A62 and IS 1570 (Part 2/Sec 1) 60C4 overlap closely enough on chemistry and mechanical properties that IS 1570 (Part 2/Sec 1) 60C4 is often considered as a substitute for BS 970 (Part 1) 060A62 in many applications. Always confirm the specific property range your application needs before substituting, and check with your supplier's mill certificate.