Post Stock Login Register

BS 970 EN14A/1 vs BS 970 (Part 1) 040A10

Related Material — 69.9% match based on chemical composition and mechanical property overlap.

BS 970 EN14A/1 (BS 970:1955) and BS 970 (Part 1) 040A10 (BS 970 (Part 1):1991) are both steel grades. Both fall under the Carbon Steel category. BS 970 EN14A/1 is typically used for bars and billets for forging; forgings and drop-forgings; bars for machining. purchaser to state hot rolled or normalised., while BS 970 (Part 1) 040A10 is commonly used for used for bolts, studs, shafts, brackets, fabricated components, and general engineering parts.. BS 970 EN14A/1 is defined under British Standards (BS), originating from United Kingdom, while BS 970 (Part 1) 040A10 is defined under British Standards (BS), originating from United Kingdom.

As per chemical composition, BS 970 EN14A/1 vs BS 970 (Part 1) 040A10 is a 78.3% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a related material overall at 69.9%.

Frequently Compared With BS 970 EN14A/1:
BS 970 (Part 3) 070M20 BS 970 (Part 1) 040A12 BS 970 (Part 1) 045A10 BS 970 (Part 1) 045A10 BS 970 (Part 3) 045A10 BS 970 (Part 1) 055M15 BS 970 (Part 1) 040A04 BS 970 (Part 1) 045M10 BS 970 (Part 1) 045M10 BS 970 (Part 3) 045M10 BS 970 (Part 1) 060A32 BS 970 (Part 1) 060A40
Match Breakdown
CHEMISTRY MATCH
78.3%
MECHANICAL MATCH
No shared data
OVERALL
69.9%
Specifications
Property BS 970 EN14A/1 BS 970 (Part 1) 040A10
Standard BS 970:1955 BS 970 (Part 1):1991
Category Carbon Steel Carbon Steel
C (%) <=0.23 0.08-0.13
Si (%) 0.05-0.35 Not specified
Mn (%) >=1.20 0.30-0.50
Cu (%) <=0.60 Not specified
S (%) <=0.060 Not specified
P (%) <=0.060 Not specified
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property BS 970 EN14A/1 BS 970 (Part 1) 040A10
Tensile Strength 510-602 MPa (33-39 tons/sq in, converted) Not specified
Elongation ≥18% Not specified
Condition Hot rolled or normalised, ruling section 2 1/2 in, ruling section 2 1/2 in (lowest-strength condition of the standard) Not specified
Typical Applications
BS 970 EN14A/1
Bars and billets for forging; forgings and drop-forgings; bars for machining. Purchaser to state hot rolled or normalised.
BS 970 (Part 1) 040A10
Used for bolts, studs, shafts, brackets, fabricated components, and general engineering parts.
Key Differences
Can BS 970 EN14A/1 Be Substituted With BS 970 (Part 1) 040A10?
BS 970 EN14A/1 and BS 970 (Part 1) 040A10 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
Forms & Sizes Available on M-EX
BS 970 EN14A/1
No active listings currently.
BS 970 (Part 1) 040A10
Round Bar → (2 listings)
Diameter: 40–40 mm (1.57–1.57 in)
Length: 4700–5500 mm (185.04–216.54 in)
On M-EX Right Now
BS 970 EN14A/1
0 active listings and RFQs →
BS 970 (Part 1) 040A10
2 active listings and RFQs →
Frequently Asked Questions
What is the difference between BS 970 EN14A/1 and BS 970 (Part 1) 040A10?
BS 970 EN14A/1 specifies Si, Cu, S, P which are not specified for BS 970 (Part 1) 040A10.
Can BS 970 EN14A/1 be substituted with BS 970 (Part 1) 040A10?
BS 970 EN14A/1 and BS 970 (Part 1) 040A10 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.