Post Stock Login Register

BS 970 EN15 vs BS 970 (Part 1) 045A10

Minimal Match — 53.3% match based on chemical composition and mechanical property overlap.

BS 970 EN15 (BS 970:1955) and BS 970 (Part 1) 045A10 (BS 970 (Part 1):1991) are both steel grades. Both fall under the Carbon Steel category. BS 970 EN15 is typically used for heavy duty shafts, couplings, general engineering, while BS 970 (Part 1) 045A10 is commonly used for case hardening steel (section four). BS 970 EN15 is defined under British Standards (BS), originating from United Kingdom, while BS 970 (Part 1) 045A10 is defined under British Standards (BS), originating from United Kingdom.

As per chemical composition, BS 970 EN15 vs BS 970 (Part 1) 045A10 is a 80% match. As per mechanical properties, the match is 0%. Combined, this makes them a minimal match overall at 53.3%.

Frequently Compared With BS 970 EN15:
BS 970 (Part 3) 070M55 BS 970 (Part 1) 080A20 BS 970 (Part 1) 040A10 BS 970 (Part 1) 040A04 BS 970 (Part 3) 045A10 BS 970 (Part 1) 040A12 BS 970 (Part 1) 045A10 BS 970 (Part 1) 045M10 BS 970 (Part 1) 055M15 BS 970 (Part 1) 045M10 BS 970 (Part 3) 045M10 BS 970 (Part 1) 060A32
Match Breakdown
CHEMISTRY MATCH
80%
MECHANICAL MATCH
0%
OVERALL
53.3%
Specifications
Property BS 970 EN15 BS 970 (Part 1) 045A10
Standard BS 970:1955 BS 970 (Part 1):1991
Category Carbon Steel Carbon Steel
C (%) 0.30-0.40 0.08-0.13
Si (%) 0.10-0.35 Not specified
Mn (%) 1.30-1.70 0.30-0.60
S (%) <=0.050 Not specified
P (%) <=0.050 Not specified
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property BS 970 EN15 BS 970 (Part 1) 045A10
Tensile Strength ≥618 MPa (40 tons/sq in, converted) 430 MPa min
Yield Strength ≥432 MPa (28 tons/sq in, converted) Not specified
Elongation ≥22% 18 % min
Hardness 179-229 HB Not specified
Condition Hardened and tempered Q, ruling section 6 in (lowest-strength condition of the standard) Case hardened, 19 mm test bar
Typical Applications
BS 970 EN15
Heavy duty shafts, couplings, general engineering
BS 970 (Part 1) 045A10
Case hardening steel (section four)
Key Differences
Can BS 970 EN15 Be Substituted With BS 970 (Part 1) 045A10?
BS 970 EN15 and BS 970 (Part 1) 045A10 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
Forms & Sizes Available on M-EX
BS 970 EN15
Round Bar → (3 listings)
Diameter: 40–40 mm (1.57–1.57 in)
Length: 5500–6400 mm (216.54–251.97 in)
BS 970 (Part 1) 045A10
No active listings currently.
On M-EX Right Now
BS 970 EN15
3 active listings and RFQs →
BS 970 (Part 1) 045A10
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between BS 970 EN15 and BS 970 (Part 1) 045A10?
BS 970 EN15 specifies Si, S, P which are not specified for BS 970 (Part 1) 045A10.
Can BS 970 EN15 be substituted with BS 970 (Part 1) 045A10?
BS 970 EN15 and BS 970 (Part 1) 045A10 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.