Post Stock Login Register

BS 970 EN32M vs BS 970 (Part 1) 214A15

Close Alternative — 84.8% match based on chemical composition and mechanical property overlap.

BS 970 EN32M (BS 970:1955) and BS 970 (Part 1) 214A15 (BS 970 (Part 1):1983) are both steel grades. Both fall under the Free Machining Steel category. BS 970 EN32M is typically used for bars and billets for forging; forgings and drop-forgings; bars for machining; bright bars., while BS 970 (Part 1) 214A15 is commonly used for case hardening steel for mechanical and allied engineering purposes (table 11 mechanical properties).. BS 970 EN32M is defined under British Standards (BS), originating from United Kingdom, while BS 970 (Part 1) 214A15 is defined under British Standards (BS), originating from United Kingdom.

As per chemical composition, BS 970 EN32M vs BS 970 (Part 1) 214A15 is a 84.8% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a close alternative overall at 84.8%.

Frequently Compared With BS 970 EN32M:
IS 1570 (Part 3) 10C8S10 IS 4432 10C8S10 SAE J403 1117 SAE J403 1118 SAE J403 1118 SAE J403 1118 SAE J403 1126 SAE J403 1126 SAE J403 1126 SAE J403 1132 SAE J403 1117 SAE J403 1117
Match Breakdown
CHEMISTRY MATCH
84.8%
MECHANICAL MATCH
No shared data
OVERALL
84.8%
Specifications
Property BS 970 EN32M BS 970 (Part 1) 214A15
Standard BS 970:1955 BS 970 (Part 1):1983
Category Free Machining Steel Free Machining Steel
C (%) 0.10-0.18 0.13-0.18
Si (%) 0.05-0.35 Not specified
Mn (%) 0.90-1.20 1.20-1.50
S (%) 0.10-0.15 0.10-0.18
P (%) <=0.050 <=0.050
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property BS 970 EN32M BS 970 (Part 1) 214A15
Tensile Strength ≥494 MPa (32 tons/sq in, converted) Not specified
Elongation ≥20% Not specified
Condition Core, after heat treatment (lowest-strength condition of the standard) Not specified
Typical Applications
BS 970 EN32M
Bars and billets for forging; forgings and drop-forgings; bars for machining; bright bars.
BS 970 (Part 1) 214A15
Case hardening steel for mechanical and allied engineering purposes (Table 11 mechanical properties).
Key Differences
Can BS 970 EN32M Be Substituted With BS 970 (Part 1) 214A15?
BS 970 EN32M and BS 970 (Part 1) 214A15 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.
On M-EX Right Now
BS 970 EN32M
0 active listings and RFQs →
BS 970 (Part 1) 214A15
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between BS 970 EN32M and BS 970 (Part 1) 214A15?
BS 970 EN32M specifies Si which is not specified for BS 970 (Part 1) 214A15.
Can BS 970 EN32M be substituted with BS 970 (Part 1) 214A15?
BS 970 EN32M and BS 970 (Part 1) 214A15 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.