Post Stock Login Register

BS 970 EN356 vs EN 10028-2 10CrMo9-10

Minimal Match — 33% match based on chemical composition and mechanical property overlap.

BS 970 EN356 (BS 970:1955) and EN 10028-2 10CrMo9-10 (EN 10028-2:2017) are both steel grades. Both fall under the Alloy Steel category. BS 970 EN356 is typically used for heavily stressed gears, differential components, while EN 10028-2 10CrMo9-10 is commonly used for flat products for pressure purposes. BS 970 EN356 is defined under British Standards (BS), originating from United Kingdom, while EN 10028-2 10CrMo9-10 is defined under European Standard (EN), originating from Europe.

As per chemical composition, BS 970 EN356 vs EN 10028-2 10CrMo9-10 is a 49.5% match. As per mechanical properties, the match is 0%. Combined, this makes them a minimal match overall at 33%.

Frequently Compared With BS 970 EN356:
NF A35-565 100C6 UNI 11234 100Cr6 GB/T 3077 12Cr2Ni4A GOST 4543 12HN3A IS 1570 (Part 4) 103Cr6 IS 4367 07Cr4Mo6 IS 1570 (Part 4) 105Cr5 IS 1570 (Part 4) 07Cr4Mo6 IS 1570 (Part 7) 10Cr36Mo10H IS 1570 (Part 4) 103Cr4 IS 1570 (Part 4) 10Cr20Mo6 IS 4367 10Cr9Mo10
Match Breakdown
CHEMISTRY MATCH
49.5%
MECHANICAL MATCH
0%
OVERALL
33%
Specifications
Property BS 970 EN356 EN 10028-2 10CrMo9-10
Standard BS 970:1955 EN 10028-2:2017
Category Alloy Steel Alloy Steel
C (%) 0.14–0.20 0.08-0.14
Mn (%) 0.35–0.65 0.40-0.80
Cr (%) 0.90–1.30 2.00-2.50
Ni (%) 3.90–4.30 Not specified
Si (%) Not specified <=0.50
P (%) Not specified <=0.020
S (%) Not specified <=0.010
N (%) Not specified <=0.012
Cu (%) Not specified <=0.30
Mo (%) Not specified 0.90-1.10
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property BS 970 EN356 EN 10028-2 10CrMo9-10
Tensile Strength 850–1000 MPa 480-630 MPa
Case Hardness HRC 60–64 Not specified
Elongation ≥12% >=18%
Yield Strength Not specified >=310 MPa
Condition Not specified Usual delivery condition normalized and tempered (+NT), nominal thickness up to 16 mm; transverse direction, Yield Strength is ReH, Elongation is A
Typical Applications
BS 970 EN356
Heavily stressed gears, differential components
EN 10028-2 10CrMo9-10
Flat products for pressure purposes
Key Differences
Can BS 970 EN356 Be Substituted With EN 10028-2 10CrMo9-10?
BS 970 EN356 and EN 10028-2 10CrMo9-10 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
Forms & Sizes Available on M-EX
BS 970 EN356
Round Bar → (3 listings)
Diameter: 50–50 mm (1.97–1.97 in)
Length: 3900–5900 mm (153.54–232.28 in)
EN 10028-2 10CrMo9-10
No active listings currently.
On M-EX Right Now
BS 970 EN356
3 active listings and RFQs →
EN 10028-2 10CrMo9-10
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between BS 970 EN356 and EN 10028-2 10CrMo9-10?
BS 970 EN356 specifies Ni which is not specified for EN 10028-2 10CrMo9-10. EN 10028-2 10CrMo9-10 specifies Si, P, S, N which are not specified for BS 970 EN356.
Can BS 970 EN356 be substituted with EN 10028-2 10CrMo9-10?
BS 970 EN356 and EN 10028-2 10CrMo9-10 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.