Post Stock Login Register

BS 970 (Part 3) 080M30 vs BS 970 (Part 1) 040A12

Related Material — 69.9% match based on chemical composition and mechanical property overlap.

BS 970 (Part 3) 080M30 (BS 970 (Part 3):1991) and BS 970 (Part 1) 040A12 (BS 970 (Part 1):1991) are both steel grades. Both fall under the Carbon Steel category. BS 970 (Part 3) 080M30 is typically used for used for shafts, gears, axles, couplings, bolts, and general engineering components., while BS 970 (Part 1) 040A12 is commonly used for as-rolled, or as-rolled and softened, steel (section two). BS 970 (Part 3) 080M30 is defined under British Standards (BS), originating from United Kingdom, while BS 970 (Part 1) 040A12 is defined under British Standards (BS), originating from United Kingdom.

As per chemical composition, BS 970 (Part 3) 080M30 vs BS 970 (Part 1) 040A12 is a 80% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a related material overall at 69.9%.

Frequently Compared With BS 970 (Part 3) 080M30:
BS 970 (Part 1) 040A10 BS 970 (Part 1) 080A20 BS 970 (Part 3) 070M55 BS 970 (Part 1) 045A10 BS 970 (Part 3) 045A10 BS 970 (Part 1) 040A04 BS 970 (Part 1) 045A10 BS 970 (Part 1) 045M10 BS 970 (Part 1) 045M10 BS 970 (Part 3) 045M10 BS 970 (Part 1) 055M15 BS 970 (Part 1) 060A32
Match Breakdown
CHEMISTRY MATCH
80%
MECHANICAL MATCH
No shared data
OVERALL
69.9%
Specifications
Property BS 970 (Part 3) 080M30 BS 970 (Part 1) 040A12
Standard BS 970 (Part 3):1991 BS 970 (Part 1):1991
Category Carbon Steel Carbon Steel
C (%) 0.26-0.34 0.10-0.15
Si (%) 0.10-0.40 Not specified
Mn (%) 0.60-1.00 0.30-0.50
P (%) <=0.05 Not specified
S (%) <=0.05 Not specified
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Typical Applications
BS 970 (Part 3) 080M30
Used for shafts, gears, axles, couplings, bolts, and general engineering components.
BS 970 (Part 1) 040A12
As-rolled, or as-rolled and softened, steel (section two)
Key Differences
Can BS 970 (Part 3) 080M30 Be Substituted With BS 970 (Part 1) 040A12?
BS 970 (Part 3) 080M30 and BS 970 (Part 1) 040A12 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
Forms & Sizes Available on M-EX
BS 970 (Part 3) 080M30
Round Bar → (2 listings)
Diameter: 40–40 mm (1.57–1.57 in)
Length: 5300–6500 mm (208.66–255.91 in)
BS 970 (Part 1) 040A12
No active listings currently.
On M-EX Right Now
BS 970 (Part 3) 080M30
2 active listings and RFQs →
BS 970 (Part 1) 040A12
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between BS 970 (Part 3) 080M30 and BS 970 (Part 1) 040A12?
BS 970 (Part 3) 080M30 specifies Si, P, S which are not specified for BS 970 (Part 1) 040A12.
Can BS 970 (Part 3) 080M30 be substituted with BS 970 (Part 1) 040A12?
BS 970 (Part 3) 080M30 and BS 970 (Part 1) 040A12 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.