Post Stock Login Register

BS 970 (Part 3) 316S33 vs EN 10088-1 1.4301

Minimal Match — 35% match based on chemical composition and mechanical property overlap.

BS 970 (Part 3) 316S33 (BS 970 (Part 3):1991) and EN 10088-1 1.4301 (EN 10088-1:2014) are both steel grades. Both fall under the Stainless Steel category. BS 970 (Part 3) 316S33 is typically used for bright cold finished bars (cold drawn, turned or precision ground) for general engineering purposes, in straight lengths; austenitic stainless and heat resisting steel (table 18), while EN 10088-1 1.4301 is commonly used for food equipment, chemical vessels, architectural, kitchenware. BS 970 (Part 3) 316S33 is defined under British Standards (BS), originating from United Kingdom, while EN 10088-1 1.4301 is defined under European Standard (EN), originating from Europe.

As per chemical composition, BS 970 (Part 3) 316S33 vs EN 10088-1 1.4301 is a 63.3% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a minimal match overall at 35%.

Frequently Compared With BS 970 (Part 3) 316S33:
ASTM A959 .- IS 1570 (Part 7) 12Cr12MoH GOST 5632 08X18H10 EN 10088-1 1.4006 IS 1570 (Part 7) 12Cr13H GB/T 3280 06Cr19Ni10 GOST 5632 06Kh23N28 EN 10088-1 1.4401 EN 10088-1 1.4845 IS 1570 (Part 7) 11Cr17Ni13W3TiH IS 1570 (Part 7) 12Cr12MoVH IS 1570 (Part 7) 12Cr12Ni2Mo
Match Breakdown
CHEMISTRY MATCH
63.3%
MECHANICAL MATCH
No shared data
OVERALL
35%
Specifications
Property BS 970 (Part 3) 316S33 EN 10088-1 1.4301
Standard BS 970 (Part 3):1991 EN 10088-1:2014
Category Stainless Steel Stainless Steel
C (%) <=0.07 ≤0.07
Si (%) <=1.0 ≤1.00
Mn (%) <=2.0 ≤2.00
P (%) <=0.045 ≤0.045
S (%) <=0.030 ≤0.030
Cr (%) 16.5-18.5 17.5–19.5
Mo (%) 2.50-3.00 Not specified
Ni (%) 11.0-14.0 8.0–10.5
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property BS 970 (Part 3) 316S33 EN 10088-1 1.4301
Tensile Strength Not specified ≥520 MPa
Yield Strength Not specified ≥210 MPa
Elongation Not specified ≥45%
Hardness Not specified ≤215 HB
Typical Applications
BS 970 (Part 3) 316S33
Bright cold finished bars (cold drawn, turned or precision ground) for general engineering purposes, in straight lengths; austenitic stainless and heat resisting steel (Table 18)
EN 10088-1 1.4301
Food equipment, chemical vessels, architectural, kitchenware
Key Differences
Can BS 970 (Part 3) 316S33 Be Substituted With EN 10088-1 1.4301?
BS 970 (Part 3) 316S33 and EN 10088-1 1.4301 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
Forms & Sizes Available on M-EX
BS 970 (Part 3) 316S33
No active listings currently.
EN 10088-1 1.4301
Sheet → (3 listings)
Thickness: 6–6 mm (0.24–0.24 in)
Width: 1250–1250 mm (49.21–49.21 in)
Length: 2500–3300 mm (98.43–129.92 in)
On M-EX Right Now
BS 970 (Part 3) 316S33
0 active listings and RFQs →
EN 10088-1 1.4301
3 active listings and RFQs →
Frequently Asked Questions
What is the difference between BS 970 (Part 3) 316S33 and EN 10088-1 1.4301?
BS 970 (Part 3) 316S33 specifies Mo which is not specified for EN 10088-1 1.4301.
Can BS 970 (Part 3) 316S33 be substituted with EN 10088-1 1.4301?
BS 970 (Part 3) 316S33 and EN 10088-1 1.4301 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.