Post Stock Login Register

DIN 17210 15Cr3 vs BS 970 (Part 1) 527M17

Close Alternative — 84.6% match based on chemical composition and mechanical property overlap.

DIN 17210 15Cr3 (DIN 17210:1986) and BS 970 (Part 1) 527M17 (BS 970 (Part 1):1983) are both steel grades. Both fall under the Alloy Steel category. DIN 17210 15Cr3 is typically used for low-alloy chromium case-hardening (carburizing) steel; gears, shafts, pins, and machine components requiring a hard wear-resistant carburized surface with a tough core, while BS 970 (Part 1) 527M17 is commonly used for case hardening steel for mechanical and allied engineering purposes (table 11 mechanical properties).. DIN 17210 15Cr3 is defined under Deutsches Institut fur Normung (DIN), originating from Germany, while BS 970 (Part 1) 527M17 is defined under British Standards (BS), originating from United Kingdom.

As per chemical composition, DIN 17210 15Cr3 vs BS 970 (Part 1) 527M17 is a 84.6% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a close alternative overall at 84.6%.

Frequently Compared With DIN 17210 15Cr3:
NF A35-565 100C6 GB/T 3077 12Cr2Ni4A IS 1570 (Part 4) 103Cr4 IS 1570 (Part 4) 103Cr6 IS 1570 (Part 4) 07Cr4Mo6 IS 1570 (Part 4) 10Cr20Mo6 UNI 11234 100Cr6 IS 4367 07Cr4Mo6 IS 4367 10Cr9Mo10 GOST 4543 12HN3A IS 1570 (Part 4) 105Cr5 IS 1570 (Part 4) 10Mo6
Match Breakdown
CHEMISTRY MATCH
84.6%
MECHANICAL MATCH
No shared data
OVERALL
84.6%
Specifications
Property DIN 17210 15Cr3 BS 970 (Part 1) 527M17
Standard DIN 17210:1986 BS 970 (Part 1):1983
Category Alloy Steel Alloy Steel
C (%) 0.12-0.18 0.14-0.20
Mn (%) 0.40-0.70 0.70-1.00
Si (%) <=0.40 Not specified
P (%) <=0.040 <=0.035
S (%) <=0.040 <=0.040
Cr (%) 0.60-0.90 0.60-0.90
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property DIN 17210 15Cr3 BS 970 (Part 1) 527M17
Tensile Strength 490-640 MPa Not specified
Yield Strength 295 MPa min Not specified
Elongation 18% min Not specified
Hardness 143-187 HB Not specified
Typical Applications
DIN 17210 15Cr3
Low-alloy chromium case-hardening (carburizing) steel; gears, shafts, pins, and machine components requiring a hard wear-resistant carburized surface with a tough core
BS 970 (Part 1) 527M17
Case hardening steel for mechanical and allied engineering purposes (Table 11 mechanical properties).
Key Differences
Can DIN 17210 15Cr3 Be Substituted With BS 970 (Part 1) 527M17?
DIN 17210 15Cr3 and BS 970 (Part 1) 527M17 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.
Forms & Sizes Available on M-EX
DIN 17210 15Cr3
Round Bar → (2 listings)
Diameter: 50–50 mm (1.97–1.97 in)
Length: 5500–6200 mm (216.54–244.09 in)
BS 970 (Part 1) 527M17
No active listings currently.
On M-EX Right Now
DIN 17210 15Cr3
2 active listings and RFQs →
BS 970 (Part 1) 527M17
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between DIN 17210 15Cr3 and BS 970 (Part 1) 527M17?
DIN 17210 15Cr3 specifies Si which is not specified for BS 970 (Part 1) 527M17.
Can DIN 17210 15Cr3 be substituted with BS 970 (Part 1) 527M17?
DIN 17210 15Cr3 and BS 970 (Part 1) 527M17 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.