Post Stock Login Register

DIN 17211 41CrAlMo7-4 vs EN 10028-2 10CrMo9-10

Minimal Match — 37.5% match based on chemical composition and mechanical property overlap.

DIN 17211 41CrAlMo7-4 (DIN 17211:1987) and EN 10028-2 10CrMo9-10 (EN 10028-2:2017) are both steel grades. Both fall under the Alloy Steel category. DIN 17211 41CrAlMo7-4 is typically used for used for nitrided shafts, gears, crankshafts, spindles, extrusion screws, and wear-resistant machine components., while EN 10028-2 10CrMo9-10 is commonly used for flat products for pressure purposes. DIN 17211 41CrAlMo7-4 is defined under Deutsches Institut fur Normung (DIN), originating from Germany, while EN 10028-2 10CrMo9-10 is defined under European Standard (EN), originating from Europe.

As per chemical composition, DIN 17211 41CrAlMo7-4 vs EN 10028-2 10CrMo9-10 is a 56.3% match. As per mechanical properties, the match is 0%. Combined, this makes them a minimal match overall at 37.5%.

Frequently Compared With DIN 17211 41CrAlMo7-4:
NF A35-565 100C6 GB/T 3077 12Cr2Ni4A GOST 4543 12HN3A UNI 11234 100Cr6 IS 1570 (Part 4) 103Cr6 IS 1570 (Part 4) 07Cr4Mo6 IS 1570 (Part 4) 103Cr4 IS 1570 (Part 4) 105Cr5 IS 1570 (Part 4) 10Cr20Mo6 IS 4367 07Cr4Mo6 IS 4367 10Cr9Mo10 IS 1570 (Part 7) 10Cr36Mo10H
Match Breakdown
CHEMISTRY MATCH
56.3%
MECHANICAL MATCH
0%
OVERALL
37.5%
Specifications
Property DIN 17211 41CrAlMo7-4 EN 10028-2 10CrMo9-10
Standard DIN 17211:1987 EN 10028-2:2017
Category Alloy Steel Alloy Steel
C (%) 0.38–0.48 0.08-0.14
Mn (%) 0.40–0.70 0.40-0.80
Cr (%) 1.40–1.80 2.00-2.50
Mo (%) 0.20–0.30 0.90-1.10
Al (%) 0.85–1.20 Not specified
Si (%) Not specified <=0.50
P (%) Not specified <=0.020
S (%) Not specified <=0.010
N (%) Not specified <=0.012
Cu (%) Not specified <=0.30
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property DIN 17211 41CrAlMo7-4 EN 10028-2 10CrMo9-10
Tensile Strength 900–1050 MPa 480-630 MPa
Surface Hardness HV ≥950 (nitrided) Not specified
Yield Strength Not specified >=310 MPa
Elongation Not specified >=18%
Condition Not specified Usual delivery condition normalized and tempered (+NT), nominal thickness up to 16 mm; transverse direction, Yield Strength is ReH, Elongation is A
Typical Applications
DIN 17211 41CrAlMo7-4
Used for nitrided shafts, gears, crankshafts, spindles, extrusion screws, and wear-resistant machine components.
EN 10028-2 10CrMo9-10
Flat products for pressure purposes
Key Differences
Can DIN 17211 41CrAlMo7-4 Be Substituted With EN 10028-2 10CrMo9-10?
DIN 17211 41CrAlMo7-4 and EN 10028-2 10CrMo9-10 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
Forms & Sizes Available on M-EX
DIN 17211 41CrAlMo7-4
Round Bar → (4 listings)
Diameter: 50–50 mm (1.97–1.97 in)
Length: 4800–6900 mm (188.98–271.65 in)
EN 10028-2 10CrMo9-10
No active listings currently.
On M-EX Right Now
DIN 17211 41CrAlMo7-4
4 active listings and RFQs →
EN 10028-2 10CrMo9-10
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between DIN 17211 41CrAlMo7-4 and EN 10028-2 10CrMo9-10?
DIN 17211 41CrAlMo7-4 specifies Al which is not specified for EN 10028-2 10CrMo9-10. EN 10028-2 10CrMo9-10 specifies Si, P, S, N which are not specified for DIN 17211 41CrAlMo7-4.
Can DIN 17211 41CrAlMo7-4 be substituted with EN 10028-2 10CrMo9-10?
DIN 17211 41CrAlMo7-4 and EN 10028-2 10CrMo9-10 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.