Post Stock Login Register

EN 10083-2 C60 vs IS 1570 (Part 4) 10Mo6

Related Material — 65% match based on chemical composition and mechanical property overlap.

EN 10083-2 C60 (EN 10083-2:2006) and IS 1570 (Part 4) 10Mo6 (IS 1570 (Part 4):1988) are both steel grades. EN 10083-2 C60 is classified under Carbon Steel, while IS 1570 (Part 4) 10Mo6 is classified under Alloy Steel — a different category, which is worth noting alongside the chemistry match below. EN 10083-2 C60 is defined under European Standard (EN), originating from Europe, while IS 1570 (Part 4) 10Mo6 is defined under Bureau of Indian Standards (IS), originating from India.

As per chemical composition, EN 10083-2 C60 vs IS 1570 (Part 4) 10Mo6 is a 68.1% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a related material overall at 65%.

Frequently Compared With EN 10083-2 C60:
BS 970 (Part 1) 040A10 BS 970 (Part 3) 070M55 BS 970 (Part 3) 045A10 BS 970 (Part 1) 040A04 BS 970 (Part 1) 045M10 BS 970 (Part 1) 045A10 BS 970 (Part 3) 045M10 BS 970 (Part 1) 055M15 BS 970 (Part 1) 060A32 BS 970 (Part 1) 040A12 BS 970 (Part 1) 045A10 BS 970 (Part 1) 045M10
Match Breakdown
CHEMISTRY MATCH
68.1%
MECHANICAL MATCH
No shared data
OVERALL
65%
Specifications
Property EN 10083-2 C60 IS 1570 (Part 4) 10Mo6
Standard EN 10083-2:2006 IS 1570 (Part 4):1988
Category Carbon Steel Alloy Steel
C (%) 0.57-0.65 <=0.15
Cr (%) <=0.40 <=0.25
Cr+Mo+Ni (%) <=0.63 Not specified
Mn (%) 0.60-0.90 0.40-0.70
Mo (%) <=0.10 0.45-0.65
Ni (%) <=0.40 <=0.30
P (%) <=0.045 Not specified
S (%) <=0.045 Not specified
Si (%) <=0.40 0.15-0.25
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property EN 10083-2 C60 IS 1570 (Part 4) 10Mo6
Condition Quenched and tempered (+QT), ruling section d <= 16 mm Not specified
Elongation 11% min Not specified
Hardness Soft annealed (+A): 241 HBW max Not specified
Tensile Strength 850 to 1 000 MPa Not specified
Yield Strength 580 MPa min Not specified
Typical Applications
EN 10083-2 C60
Used in springs, knives, wear plates, high-strength wires, and hand tools.
IS 1570 (Part 4) 10Mo6
Not documented
Key Differences
Can EN 10083-2 C60 Be Substituted With IS 1570 (Part 4) 10Mo6?
EN 10083-2 C60 and IS 1570 (Part 4) 10Mo6 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
Forms & Sizes Available on M-EX
EN 10083-2 C60
Round Bar → (2 listings)
Diameter: 40–40 mm (1.57–1.57 in)
Length: 5100–6100 mm (200.79–240.16 in)
IS 1570 (Part 4) 10Mo6
No active listings currently.
On M-EX Right Now
EN 10083-2 C60
2 active listings and RFQs →
IS 1570 (Part 4) 10Mo6
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between EN 10083-2 C60 and IS 1570 (Part 4) 10Mo6?
Different category: EN 10083-2 C60 is Carbon Steel, IS 1570 (Part 4) 10Mo6 is Alloy Steel. EN 10083-2 C60 specifies Cr+Mo+Ni, P, S which are not specified for IS 1570 (Part 4) 10Mo6.
Can EN 10083-2 C60 be substituted with IS 1570 (Part 4) 10Mo6?
EN 10083-2 C60 and IS 1570 (Part 4) 10Mo6 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.