Post Stock Login Register

EN 10025-2 S275JR vs CSA G40.21 260W

Close Alternative — 73.3% match based on chemical composition and mechanical property overlap.

EN 10025-2 S275JR (EN 10025-2:2019) and CSA G40.21 260W (CSA G40.21-13 (R2023)) are both steel grades. Both fall under the Structural Steel category. EN 10025-2 S275JR is typically used for general structural work, bridges, machinery frames, while CSA G40.21 260W is commonly used for bridges, buildings, general structural fabrication, storage tanks, older infrastructure projects.. EN 10025-2 S275JR is defined under European Standard (EN), originating from Europe, while CSA G40.21 260W is defined under Canadian Standards Association (CSA), originating from Canada.

As per chemical composition, EN 10025-2 S275JR vs CSA G40.21 260W is a 89.1% match. As per mechanical properties, the match is 41.7%. Combined, this makes them a close alternative overall at 73.3%.

Frequently Compared With EN 10025-2 S275JR:
CSA G40.21 400A CSA G40.21 400W CSA G40.21 480W ASTM A1008 SS Grade 80 ASTM A283C GOST 19281 09G2S AS/NZS 3679.1 300 CSA G40.21 300W AS/NZS 3679.1 350 CSA G40.21 350W ASTM A1008 SS Grade 50 ASTM A572 Gr.65
Match Breakdown
CHEMISTRY MATCH
89.1%
MECHANICAL MATCH
41.7%
OVERALL
73.3%
Specifications
Property EN 10025-2 S275JR CSA G40.21 260W
Standard EN 10025-2:2019 CSA G40.21-13 (R2023)
Category Structural Steel Structural Steel
C (%) <=0.21 max 0.23
Mn (%) <=1.50 max 1.4
P (%) <=0.035 max 0.035
S (%) <=0.035 max 0.035
N (%) <=0.012 Not specified
Cu (%) <=0.55 Not specified
Si (%) Not specified max 0.4
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property EN 10025-2 S275JR CSA G40.21 260W
Tensile Strength 410-560 MPa 410-590 MPa
Yield Strength >=275 MPa 260 MPa min
Elongation >=23% Not specified
Condition Nominal thickness up to 16 mm (tensile for 3 to 100 mm, elongation for 3 to 40 mm), longitudinal test pieces Not specified
Typical Applications
EN 10025-2 S275JR
General structural work, bridges, machinery frames
CSA G40.21 260W
Bridges, buildings, general structural fabrication, storage tanks, older infrastructure projects.
Key Differences
Can EN 10025-2 S275JR Be Substituted With CSA G40.21 260W?
EN 10025-2 S275JR and CSA G40.21 260W are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.
Forms & Sizes Available on M-EX
EN 10025-2 S275JR
Plate → (3 listings)
Thickness: 10–10 mm (0.39–0.39 in)
Width: 1500–1500 mm (59.06–59.06 in)
Length: 3000–3500 mm (118.11–137.8 in)
CSA G40.21 260W
Plate → (2 listings)
Thickness: 10–10 mm (0.39–0.39 in)
Width: 1500–1500 mm (59.06–59.06 in)
Length: 3400–4000 mm (133.86–157.48 in)
On M-EX Right Now
EN 10025-2 S275JR
3 active listings and RFQs →
CSA G40.21 260W
2 active listings and RFQs →
Frequently Asked Questions
What is the difference between EN 10025-2 S275JR and CSA G40.21 260W?
EN 10025-2 S275JR specifies N, Cu which are not specified for CSA G40.21 260W. CSA G40.21 260W specifies Si which is not specified for EN 10025-2 S275JR.
Can EN 10025-2 S275JR be substituted with CSA G40.21 260W?
EN 10025-2 S275JR and CSA G40.21 260W are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.