Post Stock Login Register

EN 10025-3 S420N vs GOST 19281 09G2S

Minimal Match — 35% match based on chemical composition and mechanical property overlap.

EN 10025-3 S420N (EN 10025-3:2019) and GOST 19281 09G2S (GOST 19281-2014) are both steel grades. Both fall under the Structural Steel category. EN 10025-3 S420N is defined under European Standard (EN) (Europe).

As per chemical composition, EN 10025-3 S420N vs GOST 19281 09G2S is a 65.1% match. As per mechanical properties, the match is 21.1%. Combined, this makes them a minimal match overall at 35%.

Frequently Compared With EN 10025-3 S420N:
CSA G40.21 260W AS/NZS 3679.1 350 ASTM A283C ASTM A572 Gr.65 CSA G40.21 300W CSA G40.21 350W CSA G40.21 480W ASTM A1008 SS Grade 50 ASTM A1008 SS Grade 80
Other Structural Steel Grades to Compare With EN 10025-3 S420N:
AS/NZS 3679.1 300 CSA G40.21 400A CSA G40.21 400W
Match Breakdown
CHEMISTRY MATCH
65.1%
MECHANICAL MATCH
21.1%
OVERALL
35%
Specifications
Property EN 10025-3 S420N GOST 19281 09G2S
Standard EN 10025-3:2019 GOST 19281-2014
Category Structural Steel Structural Steel
C (%) <=0.20 0.07-0.12
Si (%) <=0.60 0.5-0.8
Mn (%) 1.00-1.70 1.3-1.7
P (%) <=0.030 0.035 max
S (%) <=0.025 0.04 max
Nb (%) <=0.05 Not specified
V (%) <=0.20 Not specified
Ni (%) <=0.80 0.3 max
N (%) <=0.025 Not specified
Al (%) >=0.02 Not specified
Ti (%) <=0.05 Not specified
Cr (%) <=0.30 0.3 max
Mo (%) <=0.10 Not specified
Cu (%) <=0.55 0.3 max
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property EN 10025-3 S420N GOST 19281 09G2S
Tensile Strength 520-680 MPa 490-640 MPa
Yield Strength >=420 MPa 345 MPa min
Elongation >=19% 21% min
Condition Normalized or normalized rolled (N), nominal thickness up to 16 mm (tensile strength up to 100 mm), Table 4 Not specified
Hardness Not specified 140-190 HB
Typical Applications
EN 10025-3 S420N
Not documented
GOST 19281 09G2S
Used for bridges, pressure vessels, pipelines, structural frames, and heavy equipment components.
Key Differences
Can EN 10025-3 S420N Be Substituted With GOST 19281 09G2S?
EN 10025-3 S420N and GOST 19281 09G2S share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
Forms & Sizes Available on M-EX
EN 10025-3 S420N
No active listings currently.
GOST 19281 09G2S
Plate → (2 listings)
Thickness: 10–10 mm (0.39–0.39 in)
Width: 1500–1500 mm (59.06–59.06 in)
Length: 2900–3800 mm (114.17–149.61 in)
On M-EX Right Now
EN 10025-3 S420N
0 active listings and RFQs →
GOST 19281 09G2S
2 active listings and RFQs →
Frequently Asked Questions
What is the difference between EN 10025-3 S420N and GOST 19281 09G2S?
EN 10025-3 S420N specifies Nb, V, N, Al which are not specified for GOST 19281 09G2S.
Can EN 10025-3 S420N be substituted with GOST 19281 09G2S?
EN 10025-3 S420N and GOST 19281 09G2S share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.