Post Stock Login Register

EN 10025-5 S235J0W vs EN 10025-5 S235J2W

Strong Match — 98.4% match based on chemical composition and mechanical property overlap.

EN 10025-5 S235J0W (EN 10025-5:2019) and EN 10025-5 S235J2W (EN 10025-5:2019) are both steel grades. Both fall under the Structural Steel (Corten / Weathering) category. EN 10025-5 S235J0W is defined under European Standard (EN), originating from Europe, while EN 10025-5 S235J2W is defined under European Standard (EN), originating from Europe.

As per chemical composition, EN 10025-5 S235J0W vs EN 10025-5 S235J2W is a 97.6% match. As per mechanical properties, the match is 100%. Combined, this makes them a strong match overall at 98.4%.

Frequently Compared With EN 10025-5 S235J0W:
EN 10025-5 S355K2W EN 10025-5 S420K2W EN 10025-5 S460J2W
Other Structural Steel (Corten / Weathering) Grades to Compare With EN 10025-5 S235J0W:
CSA G40.21 260WT CSA G40.21 350A CSA G40.21 480A CSA G40.21 50W ASTM A588 ASTM A588 Grade A ASTM A588 Grade B ASTM A709 Grade HPS 70W AS/NZS 3678 Grade 350WR
Match Breakdown
CHEMISTRY MATCH
97.6%
MECHANICAL MATCH
100%
OVERALL
98.4%
Specifications
Property EN 10025-5 S235J0W EN 10025-5 S235J2W
Standard EN 10025-5:2019 EN 10025-5:2019
Category Structural Steel (Corten / Weathering) Structural Steel (Corten / Weathering)
C (%) <=0.13 <=0.13
Si (%) <=0.40 <=0.40
Mn (%) 0.20-0.60 0.20-0.60
P (%) <=0.035 <=0.035
S (%) <=0.035 <=0.030
N (%) <=0.012 Not specified
Cr (%) 0.40-0.80 0.40-0.80
Cu (%) 0.25-0.55 0.25-0.55
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property EN 10025-5 S235J0W EN 10025-5 S235J2W
Tensile Strength 360-510 MPa 360-510 MPa
Yield Strength >=235 MPa >=235 MPa
Elongation >=26% >=26%
Condition Nominal thickness up to 16 mm for yield, 3 to 100 mm for tensile, 3 to 40 mm for elongation (Lo = 5.65 sqrt(S0), longitudinal); transverse values are lower, see blocks Nominal thickness up to 16 mm for yield, 3 to 100 mm for tensile, 3 to 40 mm for elongation (Lo = 5.65 sqrt(S0), longitudinal); transverse values are lower, see blocks
Typical Applications
EN 10025-5 S235J0W
Not documented
EN 10025-5 S235J2W
Weathering (atmospheric corrosion-resistant) structural steel; bridges, railway wagons, shipping containers, transmission towers, outdoor structures exposed without protective coating
Key Differences
Can EN 10025-5 S235J0W Be Substituted With EN 10025-5 S235J2W?
EN 10025-5 S235J0W and EN 10025-5 S235J2W overlap closely enough on chemistry and mechanical properties that EN 10025-5 S235J2W is often considered as a substitute for EN 10025-5 S235J0W in many applications. Always confirm the specific property range your application needs before substituting, and check with your supplier's mill certificate.
Forms & Sizes Available on M-EX
EN 10025-5 S235J0W
No active listings currently.
EN 10025-5 S235J2W
Plate → (2 listings)
Thickness: 10–10 mm (0.39–0.39 in)
Width: 1500–1500 mm (59.06–59.06 in)
Length: 2800–3600 mm (110.24–141.73 in)
On M-EX Right Now
EN 10025-5 S235J0W
0 active listings and RFQs →
EN 10025-5 S235J2W
2 active listings and RFQs →
Frequently Asked Questions
What is the difference between EN 10025-5 S235J0W and EN 10025-5 S235J2W?
EN 10025-5 S235J0W specifies N which is not specified for EN 10025-5 S235J2W.
Can EN 10025-5 S235J0W be substituted with EN 10025-5 S235J2W?
EN 10025-5 S235J0W and EN 10025-5 S235J2W overlap closely enough on chemistry and mechanical properties that EN 10025-5 S235J2W is often considered as a substitute for EN 10025-5 S235J0W in many applications. Always confirm the specific property range your application needs before substituting, and check with your supplier's mill certificate.