Post Stock Login Register

EN 10028-2 18MnMo4-5 vs EN 10028-2 10CrMo9-10

Minimal Match — 35% match based on chemical composition and mechanical property overlap.

EN 10028-2 18MnMo4-5 (EN 10028-2:2017) and EN 10028-2 10CrMo9-10 (EN 10028-2:2017) are both steel grades. Both fall under the Alloy Steel category. EN 10028-2 18MnMo4-5 is typically used for flat products for pressure purposes, while EN 10028-2 10CrMo9-10 is commonly used for flat products for pressure purposes. EN 10028-2 18MnMo4-5 is defined under European Standard (EN), originating from Europe, while EN 10028-2 10CrMo9-10 is defined under European Standard (EN), originating from Europe.

As per chemical composition, EN 10028-2 18MnMo4-5 vs EN 10028-2 10CrMo9-10 is a 60.7% match. As per mechanical properties, the match is 23.5%. Combined, this makes them a minimal match overall at 35%.

Frequently Compared With EN 10028-2 18MnMo4-5:
IS 1570 (Part 4) 10Mo6 IS 1570 (Part 4) 10Cr20Mo6 IS 4367 07Cr4Mo6 IS 1570 (Part 4) 103Cr6 IS 1570 (Part 7) 10Mo6H IS 1570 (Part 4) 07Cr4Mo6 NF A35-565 100C6 UNI 11234 100Cr6 IS 1570 (Part 4) 105Cr5 IS 1570 (Part 4) 103Cr4 IS 1570 (Part 7) 10Cr36Mo10H IS 4367 10Cr9Mo10
Match Breakdown
CHEMISTRY MATCH
60.7%
MECHANICAL MATCH
23.5%
OVERALL
35%
Specifications
Property EN 10028-2 18MnMo4-5 EN 10028-2 10CrMo9-10
Standard EN 10028-2:2017 EN 10028-2:2017
Category Alloy Steel Alloy Steel
C (%) <=0.20 0.08-0.14
Si (%) <=0.40 <=0.50
Mn (%) 0.90-1.50 0.40-0.80
P (%) <=0.015 <=0.020
S (%) <=0.005 <=0.010
N (%) <=0.012 <=0.012
Cr (%) <=0.30 2.00-2.50
Cu (%) <=0.30 <=0.30
Mo (%) 0.45-0.60 0.90-1.10
Ni (%) <=0.30 Not specified
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property EN 10028-2 18MnMo4-5 EN 10028-2 10CrMo9-10
Tensile Strength 510-650 MPa 480-630 MPa
Yield Strength >=345 MPa >=310 MPa
Elongation >=20% >=18%
Condition Usual delivery condition normalized and tempered (+NT), nominal thickness up to 60 mm; transverse direction, Yield Strength is ReH, Elongation is A Usual delivery condition normalized and tempered (+NT), nominal thickness up to 16 mm; transverse direction, Yield Strength is ReH, Elongation is A
Typical Applications
EN 10028-2 18MnMo4-5
Flat products for pressure purposes
EN 10028-2 10CrMo9-10
Flat products for pressure purposes
Key Differences
Can EN 10028-2 18MnMo4-5 Be Substituted With EN 10028-2 10CrMo9-10?
EN 10028-2 18MnMo4-5 and EN 10028-2 10CrMo9-10 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
On M-EX Right Now
EN 10028-2 18MnMo4-5
0 active listings and RFQs →
EN 10028-2 10CrMo9-10
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between EN 10028-2 18MnMo4-5 and EN 10028-2 10CrMo9-10?
EN 10028-2 18MnMo4-5 specifies Ni which is not specified for EN 10028-2 10CrMo9-10.
Can EN 10028-2 18MnMo4-5 be substituted with EN 10028-2 10CrMo9-10?
EN 10028-2 18MnMo4-5 and EN 10028-2 10CrMo9-10 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.