Post Stock Login Register

EN 10087 11SMn37 vs EN 10087 11SMn30

Close Alternative — 84% match based on chemical composition and mechanical property overlap.

EN 10087 11SMn37 (EN 10087:1998) and EN 10087 11SMn30 (EN 10087:1998) are both steel grades. Both fall under the Free Machining Steel category. EN 10087 11SMn37 is typically used for precision turned components, automotive parts, while EN 10087 11SMn30 is commonly used for high volume screw machine parts, bolts, studs. EN 10087 11SMn37 is defined under European Standard (EN), originating from Europe, while EN 10087 11SMn30 is defined under European Standard (EN), originating from Europe.

As per chemical composition, EN 10087 11SMn37 vs EN 10087 11SMn30 is a 92.7% match. As per mechanical properties, the match is 66.7%. Combined, this makes them a close alternative overall at 84%.

Frequently Compared With EN 10087 11SMn37:
IS 4432 10C8S10 SAE J403 1141 IS 1570 (Part 3) 10C8S10 SAE J403 1117 SAE J403 1117 SAE J403 1117 SAE J403 1118 SAE J403 1118 SAE J403 1126 SAE J403 1126 SAE J403 1126 SAE J403 1132
Match Breakdown
CHEMISTRY MATCH
92.7%
MECHANICAL MATCH
66.7%
OVERALL
84%
Specifications
Property EN 10087 11SMn37 EN 10087 11SMn30
Standard EN 10087:1998 EN 10087:1998
Category Free Machining Steel Free Machining Steel
C (%) ≤0.14 ≤0.14
Si (%) ≤0.05 ≤0.05
Mn (%) 0.90–1.30 0.90–1.30
S (%) 0.34–0.40 0.27–0.33
P (%) ≤0.110 ≤0.110
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property EN 10087 11SMn37 EN 10087 11SMn30
Tensile Strength 380–570 MPa 380–570 MPa
Elongation ≥5% ≥7%
Hardness ≤180 HB ≤180 HB
Typical Applications
EN 10087 11SMn37
Precision turned components, automotive parts
EN 10087 11SMn30
High volume screw machine parts, bolts, studs
Can EN 10087 11SMn37 Be Substituted With EN 10087 11SMn30?
EN 10087 11SMn37 and EN 10087 11SMn30 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.
Forms & Sizes Available on M-EX
EN 10087 11SMn37
Hex Bar → (3 listings)
Across Flats: 25–25 mm (0.98–0.98 in)
Length: 2500–3100 mm (98.43–122.05 in)
EN 10087 11SMn30
Hex Bar → (3 listings)
Across Flats: 25–25 mm (0.98–0.98 in)
Length: 2900–3600 mm (114.17–141.73 in)
On M-EX Right Now
EN 10087 11SMn37
3 active listings and RFQs →
EN 10087 11SMn30
3 active listings and RFQs →
Frequently Asked Questions
What is the difference between EN 10087 11SMn37 and EN 10087 11SMn30?
Both grades share a similar composition profile; see the specification table above for the exact chemistry and mechanical property values.
Can EN 10087 11SMn37 be substituted with EN 10087 11SMn30?
EN 10087 11SMn37 and EN 10087 11SMn30 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.