Post Stock Login Register

EN 10088-1 X10NiCrSi35-19 vs ASTM A240/A240M N08332

Close Alternative — 79.7% match based on chemical composition and mechanical property overlap.

EN 10088-1 X10NiCrSi35-19 (EN 10088-1:2014) and ASTM A240/A240M N08332 (ASTM A240/A240M:2025) are both steel grades. Both fall under the Stainless Steel category. EN 10088-1 X10NiCrSi35-19 is defined under European Standard (EN), originating from Europe, while ASTM A240/A240M N08332 is defined under ASTM International, originating from United States.

As per chemical composition, EN 10088-1 X10NiCrSi35-19 vs ASTM A240/A240M N08332 is a 79.7% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a close alternative overall at 79.7%.

Frequently Compared With EN 10088-1 X10NiCrSi35-19:
GB/T 3280 06Cr19Ni10 GOST 5632 06Kh23N28 GOST 5632 08X18H10 EN 10088-1 1.4006 EN 10088-1 1.4301 EN 10088-1 1.4401 EN 10088-1 1.4845 IS 1570 (Part 7) 11Cr17Ni13W3TiH IS 1570 (Part 7) 12Cr12MoH IS 1570 (Part 7) 12Cr12MoVH IS 1570 (Part 7) 12Cr12Ni2Mo IS 1570 (Part 7) 12Cr13H
Match Breakdown
CHEMISTRY MATCH
79.7%
MECHANICAL MATCH
No shared data
OVERALL
79.7%
Specifications
Property EN 10088-1 X10NiCrSi35-19 ASTM A240/A240M N08332
Standard EN 10088-1:2014 ASTM A240/A240M:2025
Category Stainless Steel Stainless Steel
C (%) <=0.15 0.05-0.10
Si (%) 1.00-2.00 0.75-1.50
Mn (%) <=2.00 <=2.00
P (%) <=0.030 <=0.030
S (%) <=0.015 <=0.030
Cr (%) 17.0-20.0 17.0-20.0
Ni (%) 33.0-37.0 34.0-37.0
N (%) <=0.10 Not specified
Cu (%) Not specified <=1.00
Pb (%) Not specified <=0.005
Sn (%) Not specified <=0.025
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property EN 10088-1 X10NiCrSi35-19 ASTM A240/A240M N08332
Tensile Strength Not specified >=462 MPa
Yield Strength Not specified >=186 MPa
Elongation Not specified >=30%
Hardness Not specified <=88 HRBW
Condition Not specified Plate, sheet and strip; yield by 0.2 percent offset
Typical Applications
EN 10088-1 X10NiCrSi35-19
Not documented
ASTM A240/A240M N08332
Pressure vessels and general applications (plate, sheet and strip)
Key Differences
Can EN 10088-1 X10NiCrSi35-19 Be Substituted With ASTM A240/A240M N08332?
EN 10088-1 X10NiCrSi35-19 and ASTM A240/A240M N08332 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.
On M-EX Right Now
EN 10088-1 X10NiCrSi35-19
0 active listings and RFQs →
ASTM A240/A240M N08332
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between EN 10088-1 X10NiCrSi35-19 and ASTM A240/A240M N08332?
EN 10088-1 X10NiCrSi35-19 specifies N which is not specified for ASTM A240/A240M N08332. ASTM A240/A240M N08332 specifies Cu, Pb, Sn which are not specified for EN 10088-1 X10NiCrSi35-19.
Can EN 10088-1 X10NiCrSi35-19 be substituted with ASTM A240/A240M N08332?
EN 10088-1 X10NiCrSi35-19 and ASTM A240/A240M N08332 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.