Post Stock Login Register

EN 10088-1 X12CrNiMoV12-3 vs ASTM A959 S41428

Close Alternative — 76.5% match based on chemical composition and mechanical property overlap.

EN 10088-1 X12CrNiMoV12-3 (EN 10088-1:2014) and ASTM A959 S41428 (ASTM A959:2011) are both steel grades. Both fall under the Stainless Steel category. EN 10088-1 X12CrNiMoV12-3 is defined under European Standard (EN), originating from Europe, while ASTM A959 S41428 is defined under ASTM International, originating from United States.

As per chemical composition, EN 10088-1 X12CrNiMoV12-3 vs ASTM A959 S41428 is a 76.5% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a close alternative overall at 76.5%.

Frequently Compared With EN 10088-1 X12CrNiMoV12-3:
IS 1570 (Part 7) 12Cr12Ni2Mo IS 1570 (Part 7) 12Cr12MoVH IS 1570 (Part 7) 11Cr17Ni13W3TiH IS 1570 (Part 7) 12Cr12MoH ASTM A959 .- GOST 5632 06Kh23N28 GOST 5632 08X18H10 EN 10088-1 1.4006 EN 10088-1 1.4401 EN 10088-1 1.4845 IS 1570 (Part 7) 12Cr13H GB/T 3280 06Cr19Ni10
Match Breakdown
CHEMISTRY MATCH
76.5%
MECHANICAL MATCH
No shared data
OVERALL
76.5%
Specifications
Property EN 10088-1 X12CrNiMoV12-3 ASTM A959 S41428
Standard EN 10088-1:2014 ASTM A959:2011
Category Stainless Steel Stainless Steel
C (%) 0.08-0.15 0.10-0.17
Si (%) <=0.50 0.10-0.35
Mn (%) 0.40-0.90 0.65-1.05
P (%) <=0.025 <=0.020
S (%) <=0.015 <=0.015
Cr (%) 11.0-12.5 11.3-12.7
Mo (%) 1.50-2.00 1.50-2.00
Ni (%) 2.00-3.00 2.3-3.2
N (%) 0.020-0.040 0.020-0.045
V (%) 0.25-0.40 0.25-0.40
Al (%) Not specified <=0.025
Cu (%) Not specified <=0.15
Sn (%) Not specified <=0.05
Ti (%) Not specified <=0.05
W (%) Not specified <=0.10
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Typical Applications
EN 10088-1 X12CrNiMoV12-3
Not documented
ASTM A959 S41428
Wrought stainless steel products; recommended composition limits for adoption by product standards (clause 1.1)
Key Differences
Can EN 10088-1 X12CrNiMoV12-3 Be Substituted With ASTM A959 S41428?
EN 10088-1 X12CrNiMoV12-3 and ASTM A959 S41428 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.
On M-EX Right Now
EN 10088-1 X12CrNiMoV12-3
0 active listings and RFQs →
ASTM A959 S41428
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between EN 10088-1 X12CrNiMoV12-3 and ASTM A959 S41428?
ASTM A959 S41428 specifies Al, Cu, Sn, Ti which are not specified for EN 10088-1 X12CrNiMoV12-3.
Can EN 10088-1 X12CrNiMoV12-3 be substituted with ASTM A959 S41428?
EN 10088-1 X12CrNiMoV12-3 and ASTM A959 S41428 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.