Post Stock Login Register

EN 10088-1 X3CrNiMoBN17-13-3 vs ASTM A240/A240M S31603

Close Alternative — 81% match based on chemical composition and mechanical property overlap.

EN 10088-1 X3CrNiMoBN17-13-3 (EN 10088-1:2014) and ASTM A240/A240M S31603 (ASTM A240/A240M:2025) are both steel grades. Both fall under the Stainless Steel category. EN 10088-1 X3CrNiMoBN17-13-3 is defined under European Standard (EN), originating from Europe, while ASTM A240/A240M S31603 is defined under ASTM International, originating from United States.

As per chemical composition, EN 10088-1 X3CrNiMoBN17-13-3 vs ASTM A240/A240M S31603 is a 81% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a close alternative overall at 81%.

Frequently Compared With EN 10088-1 X3CrNiMoBN17-13-3:
GB/T 3280 06Cr19Ni10 IS 1570 (Part 7) 12Cr12MoVH ASTM A959 .- GOST 5632 06Kh23N28 GOST 5632 08X18H10 EN 10088-1 1.4006 EN 10088-1 1.4301 EN 10088-1 1.4401 EN 10088-1 1.4845 IS 1570 (Part 7) 11Cr17Ni13W3TiH IS 1570 (Part 7) 12Cr12MoH IS 1570 (Part 7) 12Cr12Ni2Mo
Match Breakdown
CHEMISTRY MATCH
81%
MECHANICAL MATCH
No shared data
OVERALL
81%
Specifications
Property EN 10088-1 X3CrNiMoBN17-13-3 ASTM A240/A240M S31603
Standard EN 10088-1:2014 ASTM A240/A240M:2025
Category Stainless Steel Stainless Steel
C (%) <=0.04 <=0.030
Si (%) <=0.75 <=0.75
Mn (%) <=2.00 <=2.00
P (%) <=0.035 <=0.045
S (%) <=0.015 <=0.030
Cr (%) 16.0-18.0 16.0-18.0
Mo (%) 2.00-3.00 2.00-3.00
Ni (%) 12.0-14.0 10.0-14.0
N (%) 0.10-0.18 <=0.10
B (%) 0.0015-0.0050 Not specified
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property EN 10088-1 X3CrNiMoBN17-13-3 ASTM A240/A240M S31603
Tensile Strength Not specified >=485 MPa
Yield Strength Not specified >=170 MPa
Elongation Not specified >=40%
Hardness Not specified <=217 HB
Condition Not specified Plate, sheet and strip; yield by 0.2 percent offset
Typical Applications
EN 10088-1 X3CrNiMoBN17-13-3
Not documented
ASTM A240/A240M S31603
Pressure vessels and general applications (plate, sheet and strip)
Key Differences
Can EN 10088-1 X3CrNiMoBN17-13-3 Be Substituted With ASTM A240/A240M S31603?
EN 10088-1 X3CrNiMoBN17-13-3 and ASTM A240/A240M S31603 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.
On M-EX Right Now
EN 10088-1 X3CrNiMoBN17-13-3
0 active listings and RFQs →
ASTM A240/A240M S31603
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between EN 10088-1 X3CrNiMoBN17-13-3 and ASTM A240/A240M S31603?
EN 10088-1 X3CrNiMoBN17-13-3 specifies B which is not specified for ASTM A240/A240M S31603.
Can EN 10088-1 X3CrNiMoBN17-13-3 be substituted with ASTM A240/A240M S31603?
EN 10088-1 X3CrNiMoBN17-13-3 and ASTM A240/A240M S31603 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.