Post Stock Login Register

EN 10088-1 X6CrNiMo17-13-2 vs EN 10088-1 1.4006

Minimal Match — 35% match based on chemical composition and mechanical property overlap.

EN 10088-1 X6CrNiMo17-13-2 (EN 10088-1:2014) and EN 10088-1 1.4006 (EN 10088-1:2014) are both steel grades. Both fall under the Stainless Steel category. EN 10088-1 X6CrNiMo17-13-2 is defined under European Standard (EN), originating from Europe, while EN 10088-1 1.4006 is defined under European Standard (EN), originating from Europe.

As per chemical composition, EN 10088-1 X6CrNiMo17-13-2 vs EN 10088-1 1.4006 is a 50.5% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a minimal match overall at 35%.

Frequently Compared With EN 10088-1 X6CrNiMo17-13-2:
GOST 5632 06Kh23N28 IS 1570 (Part 7) 12Cr12MoH ASTM A959 .- EN 10088-1 1.4401 IS 1570 (Part 7) 12Cr13H GB/T 3280 06Cr19Ni10 GOST 5632 08X18H10 EN 10088-1 1.4301 EN 10088-1 1.4845 IS 1570 (Part 7) 11Cr17Ni13W3TiH IS 1570 (Part 7) 12Cr12MoVH IS 1570 (Part 7) 12Cr12Ni2Mo
Match Breakdown
CHEMISTRY MATCH
50.5%
MECHANICAL MATCH
No shared data
OVERALL
35%
Specifications
Property EN 10088-1 X6CrNiMo17-13-2 EN 10088-1 1.4006
Standard EN 10088-1:2014 EN 10088-1:2014
Category Stainless Steel Stainless Steel
C (%) 0.04-0.08 0.08–0.15
Si (%) <=0.75 ≤1.00
Mn (%) <=2.00 ≤1.50
P (%) <=0.035 Not specified
S (%) <=0.015 Not specified
Cr (%) 16.0-18.0 11.5–13.5
Mo (%) 2.00-2.50 Not specified
Ni (%) 12.0-14.0 ≤0.75
N (%) <=0.10 Not specified
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property EN 10088-1 X6CrNiMo17-13-2 EN 10088-1 1.4006
Tensile Strength Not specified ≥540 MPa (annealed)
Hardness HRC Not specified 36–45 (hardened)
Elongation Not specified ≥18%
Typical Applications
EN 10088-1 X6CrNiMo17-13-2
Not documented
EN 10088-1 1.4006
Cutlery, turbine blades, fasteners, surgical instruments
Key Differences
Can EN 10088-1 X6CrNiMo17-13-2 Be Substituted With EN 10088-1 1.4006?
EN 10088-1 X6CrNiMo17-13-2 and EN 10088-1 1.4006 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
Forms & Sizes Available on M-EX
EN 10088-1 X6CrNiMo17-13-2
No active listings currently.
EN 10088-1 1.4006
Sheet → (3 listings)
Thickness: 6–6 mm (0.24–0.24 in)
Width: 1250–1250 mm (49.21–49.21 in)
Length: 2700–3400 mm (106.3–133.86 in)
On M-EX Right Now
EN 10088-1 X6CrNiMo17-13-2
0 active listings and RFQs →
EN 10088-1 1.4006
3 active listings and RFQs →
Frequently Asked Questions
What is the difference between EN 10088-1 X6CrNiMo17-13-2 and EN 10088-1 1.4006?
EN 10088-1 X6CrNiMo17-13-2 specifies P, S, Mo, N which are not specified for EN 10088-1 1.4006.
Can EN 10088-1 X6CrNiMo17-13-2 be substituted with EN 10088-1 1.4006?
EN 10088-1 X6CrNiMo17-13-2 and EN 10088-1 1.4006 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.