Post Stock Login Register

EN 10088-1 X9CrMnNiCu17-8-5-2 vs EN 10088-1 1.4845

Minimal Match — 35% match based on chemical composition and mechanical property overlap.

EN 10088-1 X9CrMnNiCu17-8-5-2 (EN 10088-1:2014) and EN 10088-1 1.4845 (EN 10088-1:2014) are both steel grades. Both fall under the Stainless Steel category. EN 10088-1 X9CrMnNiCu17-8-5-2 is defined under European Standard (EN), originating from Europe, while EN 10088-1 1.4845 is defined under European Standard (EN), originating from Europe.

As per chemical composition, EN 10088-1 X9CrMnNiCu17-8-5-2 vs EN 10088-1 1.4845 is a 58.8% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a minimal match overall at 35%.

Frequently Compared With EN 10088-1 X9CrMnNiCu17-8-5-2:
GOST 5632 08X18H10 EN 10088-1 1.4006 EN 10088-1 1.4401 ASTM A959 201 ASTM A959 202 ASTM A959 .- GB/T 3280 06Cr19Ni10 GOST 5632 06Kh23N28 EN 10088-1 1.4301 IS 1570 (Part 7) 11Cr17Ni13W3TiH IS 1570 (Part 7) 12Cr12MoH IS 1570 (Part 7) 12Cr12MoVH
Match Breakdown
CHEMISTRY MATCH
58.8%
MECHANICAL MATCH
No shared data
OVERALL
35%
Specifications
Property EN 10088-1 X9CrMnNiCu17-8-5-2 EN 10088-1 1.4845
Standard EN 10088-1:2014 EN 10088-1:2014
Category Stainless Steel Stainless Steel
C (%) <=0.10 ≤0.10
Si (%) <=1.00 ≤1.50
Mn (%) 5.5-9.5 ≤2.00
P (%) <=0.070 Not specified
S (%) <=0.010 Not specified
Cr (%) 16.5-18.5 24.0–26.0
Ni (%) 4.5-5.5 19.0–22.0
N (%) <=0.15 Not specified
Cu (%) 1.00-2.50 Not specified
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property EN 10088-1 X9CrMnNiCu17-8-5-2 EN 10088-1 1.4845
Tensile Strength Not specified ≥515 MPa
Yield Strength Not specified ≥205 MPa
Elongation Not specified ≥40%
Max Service Temp Not specified 1100°C continuous
Typical Applications
EN 10088-1 X9CrMnNiCu17-8-5-2
Not documented
EN 10088-1 1.4845
Furnace parts, heat exchangers, kiln components
Key Differences
Can EN 10088-1 X9CrMnNiCu17-8-5-2 Be Substituted With EN 10088-1 1.4845?
EN 10088-1 X9CrMnNiCu17-8-5-2 and EN 10088-1 1.4845 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
Forms & Sizes Available on M-EX
EN 10088-1 X9CrMnNiCu17-8-5-2
No active listings currently.
EN 10088-1 1.4845
Sheet → (3 listings)
Thickness: 6–6 mm (0.24–0.24 in)
Width: 1250–1250 mm (49.21–49.21 in)
Length: 2700–3200 mm (106.3–125.98 in)
On M-EX Right Now
EN 10088-1 X9CrMnNiCu17-8-5-2
0 active listings and RFQs →
EN 10088-1 1.4845
3 active listings and RFQs →
Frequently Asked Questions
What is the difference between EN 10088-1 X9CrMnNiCu17-8-5-2 and EN 10088-1 1.4845?
EN 10088-1 X9CrMnNiCu17-8-5-2 specifies P, S, N, Cu which are not specified for EN 10088-1 1.4845.
Can EN 10088-1 X9CrMnNiCu17-8-5-2 be substituted with EN 10088-1 1.4845?
EN 10088-1 X9CrMnNiCu17-8-5-2 and EN 10088-1 1.4845 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.