Post Stock Login Register

EN 10088-1 X1CrNiMoAlTi12-10-2 vs EN 10088-3 X1CrNiMoAlTi12-9-2

Strong Match — 86.2% match based on chemical composition and mechanical property overlap.

EN 10088-1 X1CrNiMoAlTi12-10-2 (EN 10088-1:2023) and EN 10088-3 X1CrNiMoAlTi12-9-2 (EN 10088-3:2014) are both steel grades. Both fall under the Stainless Steel category. EN 10088-1 X1CrNiMoAlTi12-10-2 is defined under European Standard (EN), originating from Europe, while EN 10088-3 X1CrNiMoAlTi12-9-2 is defined under European Standard (EN), originating from Europe.

As per chemical composition, EN 10088-1 X1CrNiMoAlTi12-10-2 vs EN 10088-3 X1CrNiMoAlTi12-9-2 is a 86.2% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a strong match overall at 86.2%.

Frequently Compared With EN 10088-1 X1CrNiMoAlTi12-10-2:
EN 10088-1 1.4006 EN 10088-1 1.4301 GB/T 3280 06Cr19Ni10 EN 10088-1 1.4401 EN 10088-1 1.4845 ASTM A959 .- GOST 5632 06Kh23N28 GOST 5632 08X18H10 IS 1570 (Part 7) 11Cr17Ni13W3TiH IS 1570 (Part 7) 12Cr12MoH IS 1570 (Part 7) 12Cr12MoVH IS 1570 (Part 7) 12Cr12Ni2Mo
Match Breakdown
CHEMISTRY MATCH
86.2%
MECHANICAL MATCH
No shared data
OVERALL
86.2%
Specifications
Property EN 10088-1 X1CrNiMoAlTi12-10-2 EN 10088-3 X1CrNiMoAlTi12-9-2
Standard EN 10088-1:2023 EN 10088-3:2014
Category Stainless Steel Stainless Steel
C (%) <=0.015 <=0.015
Si (%) <=0.10 <=0.10
Mn (%) <=0.10 <=0.10
P (%) <=0.010 <=0.010
S (%) <=0.005 <=0.005
Cr (%) 11.5-12.5 11.5-12.5
Mo (%) 1.85-2.15 1.85-2.15
Ni (%) 9.2-10.2 8.5-9.5
Al (%) 0.80-1.10 0.60-0.80
Ti (%) 0.28-0.40 0.28-0.37
N (%) <=0.020 <=0.010
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property EN 10088-1 X1CrNiMoAlTi12-10-2 EN 10088-3 X1CrNiMoAlTi12-9-2
Tensile Strength Not specified <=1200 MPa
Hardness Not specified <=363 HB
Condition Not specified Solution annealed (+AT), conditions 1C, 1E, 1D, 1X, 1G and 2D, thickness or diameter up to 150 mm; hardness for guidance only
Typical Applications
EN 10088-1 X1CrNiMoAlTi12-10-2
Not documented
EN 10088-3 X1CrNiMoAlTi12-9-2
General purposes, semi-finished products, bars, rods, wire, sections and bright products
Can EN 10088-1 X1CrNiMoAlTi12-10-2 Be Substituted With EN 10088-3 X1CrNiMoAlTi12-9-2?
EN 10088-1 X1CrNiMoAlTi12-10-2 and EN 10088-3 X1CrNiMoAlTi12-9-2 overlap closely enough on chemistry and mechanical properties that EN 10088-3 X1CrNiMoAlTi12-9-2 is often considered as a substitute for EN 10088-1 X1CrNiMoAlTi12-10-2 in many applications. Always confirm the specific property range your application needs before substituting, and check with your supplier's mill certificate.
On M-EX Right Now
EN 10088-1 X1CrNiMoAlTi12-10-2
0 active listings and RFQs →
EN 10088-3 X1CrNiMoAlTi12-9-2
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between EN 10088-1 X1CrNiMoAlTi12-10-2 and EN 10088-3 X1CrNiMoAlTi12-9-2?
Both grades share a similar composition profile; see the specification table above for the exact chemistry and mechanical property values.
Can EN 10088-1 X1CrNiMoAlTi12-10-2 be substituted with EN 10088-3 X1CrNiMoAlTi12-9-2?
EN 10088-1 X1CrNiMoAlTi12-10-2 and EN 10088-3 X1CrNiMoAlTi12-9-2 overlap closely enough on chemistry and mechanical properties that EN 10088-3 X1CrNiMoAlTi12-9-2 is often considered as a substitute for EN 10088-1 X1CrNiMoAlTi12-10-2 in many applications. Always confirm the specific property range your application needs before substituting, and check with your supplier's mill certificate.