Post Stock Login Register

EN 10088-1 X20Cr13 vs EN 10088-1 1.4006

Close Alternative — 75.2% match based on chemical composition and mechanical property overlap.

EN 10088-1 X20Cr13 (EN 10088-1:2023) and EN 10088-1 1.4006 (EN 10088-1:2014) are both steel grades. Both fall under the Stainless Steel category. EN 10088-1 X20Cr13 is defined under European Standard (EN), originating from Europe, while EN 10088-1 1.4006 is defined under European Standard (EN), originating from Europe.

As per chemical composition, EN 10088-1 X20Cr13 vs EN 10088-1 1.4006 is a 75.2% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a close alternative overall at 75.2%.

Frequently Compared With EN 10088-1 X20Cr13:
ASTM A959 .- GOST 5632 06Kh23N28 EN 10088-1 1.4301 EN 10088-1 1.4401 EN 10088-1 1.4845 IS 1570 (Part 7) 11Cr17Ni13W3TiH IS 1570 (Part 7) 12Cr13H GB/T 3280 06Cr19Ni10 GOST 5632 08X18H10 IS 1570 (Part 7) 12Cr12MoH IS 1570 (Part 7) 12Cr12MoVH IS 1570 (Part 7) 12Cr12Ni2Mo
Match Breakdown
CHEMISTRY MATCH
75.2%
MECHANICAL MATCH
No shared data
OVERALL
75.2%
Specifications
Property EN 10088-1 X20Cr13 EN 10088-1 1.4006
Standard EN 10088-1:2023 EN 10088-1:2014
Category Stainless Steel Stainless Steel
C (%) 0.16-0.25 0.08–0.15
Si (%) <=1.00 ≤1.00
Mn (%) <=1.50 ≤1.50
P (%) <=0.040 Not specified
S (%) <=0.015 Not specified
Cr (%) 12.0-14.0 11.5–13.5
Ni (%) Not specified ≤0.75
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property EN 10088-1 X20Cr13 EN 10088-1 1.4006
Tensile Strength Not specified ≥540 MPa (annealed)
Hardness HRC Not specified 36–45 (hardened)
Elongation Not specified ≥18%
Typical Applications
EN 10088-1 X20Cr13
Not documented
EN 10088-1 1.4006
Cutlery, turbine blades, fasteners, surgical instruments
Key Differences
Can EN 10088-1 X20Cr13 Be Substituted With EN 10088-1 1.4006?
EN 10088-1 X20Cr13 and EN 10088-1 1.4006 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.
Forms & Sizes Available on M-EX
EN 10088-1 X20Cr13
No active listings currently.
EN 10088-1 1.4006
Sheet → (3 listings)
Thickness: 6–6 mm (0.24–0.24 in)
Width: 1250–1250 mm (49.21–49.21 in)
Length: 2700–3400 mm (106.3–133.86 in)
On M-EX Right Now
EN 10088-1 X20Cr13
0 active listings and RFQs →
EN 10088-1 1.4006
3 active listings and RFQs →
Frequently Asked Questions
What is the difference between EN 10088-1 X20Cr13 and EN 10088-1 1.4006?
EN 10088-1 X20Cr13 specifies P, S which are not specified for EN 10088-1 1.4006. EN 10088-1 1.4006 specifies Ni which is not specified for EN 10088-1 X20Cr13.
Can EN 10088-1 X20Cr13 be substituted with EN 10088-1 1.4006?
EN 10088-1 X20Cr13 and EN 10088-1 1.4006 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.