Post Stock Login Register

EN 10088-1 X2CrCuNbTiV22-1 vs EN 10088-3 X2CrNbCu21

Close Alternative — 79.3% match based on chemical composition and mechanical property overlap.

EN 10088-1 X2CrCuNbTiV22-1 (EN 10088-1:2023) and EN 10088-3 X2CrNbCu21 (EN 10088-3:2014) are both steel grades. Both fall under the Stainless Steel category. EN 10088-1 X2CrCuNbTiV22-1 is defined under European Standard (EN), originating from Europe, while EN 10088-3 X2CrNbCu21 is defined under European Standard (EN), originating from Europe.

As per chemical composition, EN 10088-1 X2CrCuNbTiV22-1 vs EN 10088-3 X2CrNbCu21 is a 79.3% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a close alternative overall at 79.3%.

Frequently Compared With EN 10088-1 X2CrCuNbTiV22-1:
IS 1570 (Part 7) 12Cr13H ASTM A959 .- GB/T 3280 06Cr19Ni10 GOST 5632 06Kh23N28 GOST 5632 08X18H10 EN 10088-1 1.4006 EN 10088-1 1.4301 EN 10088-1 1.4401 EN 10088-1 1.4845 IS 1570 (Part 7) 12Cr12MoH IS 1570 (Part 7) 12Cr12Ni2Mo IS 1570 (Part 7) 11Cr17Ni13W3TiH
Match Breakdown
CHEMISTRY MATCH
79.3%
MECHANICAL MATCH
No shared data
OVERALL
79.3%
Specifications
Property EN 10088-1 X2CrCuNbTiV22-1 EN 10088-3 X2CrNbCu21
Standard EN 10088-1:2023 EN 10088-3:2014
Category Stainless Steel Stainless Steel
C (%) <=0.030 <=0.030
Si (%) <=1.00 <=1.00
Mn (%) <=0.80 <=1.00
P (%) <=0.040 <=0.040
S (%) <=0.015 <=0.015
Cr (%) 20.0-24.0 20.0-21.5
N (%) <=0.030 <=0.030
Nb (%) 0.10-0.70 <=1.00
Ti (%) 0.10-0.70 Not specified
V (%) 0.03-0.50 Not specified
Cu (%) 0.30-0.80 0.10-1.00
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property EN 10088-1 X2CrCuNbTiV22-1 EN 10088-3 X2CrNbCu21
Tensile Strength Not specified 420-640 MPa
Yield Strength Not specified >=240 MPa
Elongation Not specified >=20%
Hardness Not specified <=200 HB
Condition Not specified Annealed (+A), conditions 1C, 1E, 1D, 1X, 1G and 2D, thickness or diameter up to 50 mm; Yield Strength is Rp0.2, Elongation is A (longitudinal), hardness for guidance only
Typical Applications
EN 10088-1 X2CrCuNbTiV22-1
Not documented
EN 10088-3 X2CrNbCu21
General purposes, semi-finished products, bars, rods, wire, sections and bright products
Key Differences
Can EN 10088-1 X2CrCuNbTiV22-1 Be Substituted With EN 10088-3 X2CrNbCu21?
EN 10088-1 X2CrCuNbTiV22-1 and EN 10088-3 X2CrNbCu21 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.
On M-EX Right Now
EN 10088-1 X2CrCuNbTiV22-1
0 active listings and RFQs →
EN 10088-3 X2CrNbCu21
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between EN 10088-1 X2CrCuNbTiV22-1 and EN 10088-3 X2CrNbCu21?
EN 10088-1 X2CrCuNbTiV22-1 specifies Ti, V which are not specified for EN 10088-3 X2CrNbCu21.
Can EN 10088-1 X2CrCuNbTiV22-1 be substituted with EN 10088-3 X2CrNbCu21?
EN 10088-1 X2CrCuNbTiV22-1 and EN 10088-3 X2CrNbCu21 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.