Post Stock Login Register

EN 10088-1 X2CrNiMoCuN25-6-3 vs IS 6603 X02Cr25Ni7Mo4N

Strong Match — 89.4% match based on chemical composition and mechanical property overlap.

EN 10088-1 X2CrNiMoCuN25-6-3 (EN 10088-1:2023) and IS 6603 X02Cr25Ni7Mo4N (IS 6603:2024) are both steel grades. Both fall under the Stainless Steel category. EN 10088-1 X2CrNiMoCuN25-6-3 is defined under European Standard (EN), originating from Europe, while IS 6603 X02Cr25Ni7Mo4N is defined under Bureau of Indian Standards (IS), originating from India.

As per chemical composition, EN 10088-1 X2CrNiMoCuN25-6-3 vs IS 6603 X02Cr25Ni7Mo4N is a 89.4% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a strong match overall at 89.4%.

Frequently Compared With EN 10088-1 X2CrNiMoCuN25-6-3:
EN 10088-1 1.4845 ASTM A959 .- GOST 5632 06Kh23N28 GOST 5632 08X18H10 EN 10088-1 1.4401 IS 1570 (Part 7) 11Cr17Ni13W3TiH IS 1570 (Part 7) 12Cr12MoH IS 1570 (Part 7) 12Cr12MoVH IS 1570 (Part 7) 12Cr13H GB/T 3280 06Cr19Ni10 EN 10088-1 1.4006 EN 10088-1 1.4301
Match Breakdown
CHEMISTRY MATCH
89.4%
MECHANICAL MATCH
No shared data
OVERALL
89.4%
Specifications
Property EN 10088-1 X2CrNiMoCuN25-6-3 IS 6603 X02Cr25Ni7Mo4N
Standard EN 10088-1:2023 IS 6603:2024
Category Stainless Steel Stainless Steel
C (%) <=0.030 <=0.030
Si (%) <=0.70 <=1.00
Mn (%) <=2.00 <=2.00
P (%) <=0.035 <=0.035
S (%) <=0.015 <=0.015
Cr (%) 24.0-26.0 24.0-26.0
Mo (%) 3.00-4.0 3.0-4.5
Ni (%) 6.0-8.0 6.0-8.0
N (%) 0.20-0.30 0.24-0.35
Cu (%) 1.00-2.50 Not specified
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property EN 10088-1 X2CrNiMoCuN25-6-3 IS 6603 X02Cr25Ni7Mo4N
Tensile Strength Not specified >=730 MPa
Yield Strength Not specified >=530 MPa
Elongation Not specified >=25%
Hardness Not specified <=290 HB
Condition Not specified Solution annealed, conditions 1C, 1E, 1D, 1X, 1G and 2D, thickness or diameter up to 160 mm; Tensile Strength is a minimum as printed, hardness for guidance only
Typical Applications
EN 10088-1 X2CrNiMoCuN25-6-3
Not documented
IS 6603 X02Cr25Ni7Mo4N
General purposes, semi-finished products, bars, wire rods and bright bars
Key Differences
Can EN 10088-1 X2CrNiMoCuN25-6-3 Be Substituted With IS 6603 X02Cr25Ni7Mo4N?
EN 10088-1 X2CrNiMoCuN25-6-3 and IS 6603 X02Cr25Ni7Mo4N overlap closely enough on chemistry and mechanical properties that IS 6603 X02Cr25Ni7Mo4N is often considered as a substitute for EN 10088-1 X2CrNiMoCuN25-6-3 in many applications. Always confirm the specific property range your application needs before substituting, and check with your supplier's mill certificate.
On M-EX Right Now
EN 10088-1 X2CrNiMoCuN25-6-3
0 active listings and RFQs →
IS 6603 X02Cr25Ni7Mo4N
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between EN 10088-1 X2CrNiMoCuN25-6-3 and IS 6603 X02Cr25Ni7Mo4N?
EN 10088-1 X2CrNiMoCuN25-6-3 specifies Cu which is not specified for IS 6603 X02Cr25Ni7Mo4N.
Can EN 10088-1 X2CrNiMoCuN25-6-3 be substituted with IS 6603 X02Cr25Ni7Mo4N?
EN 10088-1 X2CrNiMoCuN25-6-3 and IS 6603 X02Cr25Ni7Mo4N overlap closely enough on chemistry and mechanical properties that IS 6603 X02Cr25Ni7Mo4N is often considered as a substitute for EN 10088-1 X2CrNiMoCuN25-6-3 in many applications. Always confirm the specific property range your application needs before substituting, and check with your supplier's mill certificate.