Post Stock Login Register

EN 10088-1 X2CrNiMoCuS17-10-2 vs EN 10088-1 1.4401

Close Alternative — 75% match based on chemical composition and mechanical property overlap.

EN 10088-1 X2CrNiMoCuS17-10-2 (EN 10088-1:2023) and EN 10088-1 1.4401 (EN 10088-1:2014) are both steel grades. Both fall under the Stainless Steel category. EN 10088-1 X2CrNiMoCuS17-10-2 is defined under European Standard (EN), originating from Europe, while EN 10088-1 1.4401 is defined under European Standard (EN), originating from Europe.

As per chemical composition, EN 10088-1 X2CrNiMoCuS17-10-2 vs EN 10088-1 1.4401 is a 75% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a close alternative overall at 75%.

Frequently Compared With EN 10088-1 X2CrNiMoCuS17-10-2:
ASTM A959 .- GB/T 3280 06Cr19Ni10 EN 10088-1 1.4845 IS 1570 (Part 7) 11Cr17Ni13W3TiH GOST 5632 06Kh23N28 GOST 5632 08X18H10 EN 10088-1 1.4006 EN 10088-1 1.4301 IS 1570 (Part 7) 12Cr12MoH IS 1570 (Part 7) 12Cr12MoVH IS 1570 (Part 7) 12Cr12Ni2Mo IS 1570 (Part 7) 12Cr13H
Match Breakdown
CHEMISTRY MATCH
75%
MECHANICAL MATCH
No shared data
OVERALL
75%
Specifications
Property EN 10088-1 X2CrNiMoCuS17-10-2 EN 10088-1 1.4401
Standard EN 10088-1:2023 EN 10088-1:2014
Category Stainless Steel Stainless Steel
C (%) <=0.030 ≤0.07
Si (%) <=1.00 ≤1.00
Mn (%) <=2.00 ≤2.00
P (%) <=0.045 Not specified
S (%) 0.10-0.20 Not specified
Cr (%) 16.5-18.5 16.5–18.5
Mo (%) 2.00-2.50 2.0–2.5
Ni (%) 10.0-13.0 10.5–13.5
N (%) <=0.10 Not specified
Cu (%) 1.30-1.80 Not specified
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property EN 10088-1 X2CrNiMoCuS17-10-2 EN 10088-1 1.4401
Tensile Strength Not specified ≥520 MPa
Yield Strength Not specified ≥210 MPa
Elongation Not specified ≥40%
Hardness Not specified ≤215 HB
Typical Applications
EN 10088-1 X2CrNiMoCuS17-10-2
Not documented
EN 10088-1 1.4401
Marine, chemical processing, pharmaceutical equipment
Key Differences
Can EN 10088-1 X2CrNiMoCuS17-10-2 Be Substituted With EN 10088-1 1.4401?
EN 10088-1 X2CrNiMoCuS17-10-2 and EN 10088-1 1.4401 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.
Forms & Sizes Available on M-EX
EN 10088-1 X2CrNiMoCuS17-10-2
No active listings currently.
EN 10088-1 1.4401
Sheet → (4 listings)
Thickness: 6–6 mm (0.24–0.24 in)
Width: 1250–1250 mm (49.21–49.21 in)
Length: 2500–3400 mm (98.43–133.86 in)
On M-EX Right Now
EN 10088-1 X2CrNiMoCuS17-10-2
0 active listings and RFQs →
EN 10088-1 1.4401
4 active listings and RFQs →
Frequently Asked Questions
What is the difference between EN 10088-1 X2CrNiMoCuS17-10-2 and EN 10088-1 1.4401?
EN 10088-1 X2CrNiMoCuS17-10-2 specifies P, S, N, Cu which are not specified for EN 10088-1 1.4401.
Can EN 10088-1 X2CrNiMoCuS17-10-2 be substituted with EN 10088-1 1.4401?
EN 10088-1 X2CrNiMoCuS17-10-2 and EN 10088-1 1.4401 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.