Post Stock Login Register

EN 10088-1 X40CrMoVN16-2 vs EN 10088-3 X39CrMo17-1

Related Material — 64.2% match based on chemical composition and mechanical property overlap.

EN 10088-1 X40CrMoVN16-2 (EN 10088-1:2023) and EN 10088-3 X39CrMo17-1 (EN 10088-3:2014) are both steel grades. Both fall under the Stainless Steel category. EN 10088-1 X40CrMoVN16-2 is defined under European Standard (EN), originating from Europe, while EN 10088-3 X39CrMo17-1 is defined under European Standard (EN), originating from Europe.

As per chemical composition, EN 10088-1 X40CrMoVN16-2 vs EN 10088-3 X39CrMo17-1 is a 64.2% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a related material overall at 64.2%.

Frequently Compared With EN 10088-1 X40CrMoVN16-2:
GOST 5632 06Kh23N28 EN 10088-1 1.4401 IS 1570 (Part 7) 12Cr13H EN 10088-1 1.4006 EN 10088-1 1.4301 EN 10088-1 1.4845 ASTM A959 .- GB/T 3280 06Cr19Ni10 GOST 5632 08X18H10 IS 1570 (Part 7) 11Cr17Ni13W3TiH IS 1570 (Part 7) 12Cr12MoH IS 1570 (Part 7) 12Cr12MoVH
Match Breakdown
CHEMISTRY MATCH
64.2%
MECHANICAL MATCH
No shared data
OVERALL
64.2%
Specifications
Property EN 10088-1 X40CrMoVN16-2 EN 10088-3 X39CrMo17-1
Standard EN 10088-1:2023 EN 10088-3:2014
Category Stainless Steel Stainless Steel
C (%) 0.35-0.50 0.33-0.45
Si (%) <=1.00 <=1.00
Mn (%) <=1.00 <=1.50
P (%) <=0.040 <=0.040
S (%) <=0.015 <=0.030
Cr (%) 14.0-16.0 15.5-17.5
Mo (%) 1.00-2.50 0.80-1.30
Ni (%) <=0.50 <=1.00
V (%) <=1.50 Not specified
N (%) 0.10-0.30 Not specified
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property EN 10088-1 X40CrMoVN16-2 EN 10088-3 X39CrMo17-1
Tensile Strength Not specified <=900 MPa
Hardness Not specified <=280 HB
Condition Not specified Annealed (+A), conditions 1C, 1E, 1D, 1X, 1G and 2D, size range not stated; hardness for guidance only
Typical Applications
EN 10088-1 X40CrMoVN16-2
Not documented
EN 10088-3 X39CrMo17-1
General purposes, semi-finished products, bars, rods, wire, sections and bright products
Key Differences
Can EN 10088-1 X40CrMoVN16-2 Be Substituted With EN 10088-3 X39CrMo17-1?
EN 10088-1 X40CrMoVN16-2 and EN 10088-3 X39CrMo17-1 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
On M-EX Right Now
EN 10088-1 X40CrMoVN16-2
0 active listings and RFQs →
EN 10088-3 X39CrMo17-1
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between EN 10088-1 X40CrMoVN16-2 and EN 10088-3 X39CrMo17-1?
EN 10088-1 X40CrMoVN16-2 specifies V, N which are not specified for EN 10088-3 X39CrMo17-1.
Can EN 10088-1 X40CrMoVN16-2 be substituted with EN 10088-3 X39CrMo17-1?
EN 10088-1 X40CrMoVN16-2 and EN 10088-3 X39CrMo17-1 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.