Post Stock Login Register

EN 10088-1 X53CrSiMoVN16-2 vs EN 10083-2 C50E

Related Material — 56.5% match based on chemical composition and mechanical property overlap.

EN 10088-1 X53CrSiMoVN16-2 (EN 10088-1:2023) and EN 10083-2 C50E (EN 10083-2:2006) are both steel grades. EN 10088-1 X53CrSiMoVN16-2 is classified under Stainless Steel, while EN 10083-2 C50E is classified under Carbon Steel — a different category, which is worth noting alongside the chemistry match below. EN 10088-1 X53CrSiMoVN16-2 is defined under European Standard (EN), originating from Europe, while EN 10083-2 C50E is defined under European Standard (EN), originating from Europe.

As per chemical composition, EN 10088-1 X53CrSiMoVN16-2 vs EN 10083-2 C50E is a 56.5% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a related material overall at 56.5%.

Frequently Compared With EN 10088-1 X53CrSiMoVN16-2:
EN 10088-1 1.4401 GOST 5632 06Kh23N28 GOST 5632 08X18H10 EN 10088-1 1.4006 EN 10088-1 1.4301 EN 10088-1 1.4845 IS 1570 (Part 7) 12Cr12MoH IS 1570 (Part 7) 12Cr12Ni2Mo ASTM A959 .- GB/T 3280 06Cr19Ni10 IS 1570 (Part 7) 11Cr17Ni13W3TiH IS 1570 (Part 7) 12Cr12MoVH
Match Breakdown
CHEMISTRY MATCH
56.5%
MECHANICAL MATCH
No shared data
OVERALL
56.5%
Specifications
Property EN 10088-1 X53CrSiMoVN16-2 EN 10083-2 C50E
Standard EN 10088-1:2023 EN 10083-2:2006
Category Stainless Steel Carbon Steel
C (%) 0.45-0.60 0.47-0.55
Si (%) 1.30-1.70 <=0.40
Mn (%) <=0.80 0.60-0.90
P (%) <=0.030 <=0.030
S (%) <=0.010 <=0.035
Cr (%) 15.0-16.5 <=0.40
Mo (%) 0.20-0.40 <=0.10
Ni (%) <=0.40 <=0.40
V (%) 0.20-0.40 Not specified
N (%) 0.05-0.20 Not specified
Cr+Mo+Ni (%) Not specified <=0.63
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property EN 10088-1 X53CrSiMoVN16-2 EN 10083-2 C50E
Condition Not specified Quenched and tempered (+QT), ruling section d <= 16 mm
Elongation Not specified 13% min
Hardness Not specified Soft annealed (+A): 217 HBW max
Tensile Strength Not specified 750 to 900 MPa
Yield Strength Not specified 520 MPa min
Typical Applications
EN 10088-1 X53CrSiMoVN16-2
Not documented
EN 10083-2 C50E
Quenched and tempered, flame or induction hardened machine parts; can also be used normalized (clause 1)
Key Differences
Can EN 10088-1 X53CrSiMoVN16-2 Be Substituted With EN 10083-2 C50E?
EN 10088-1 X53CrSiMoVN16-2 and EN 10083-2 C50E share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
On M-EX Right Now
EN 10088-1 X53CrSiMoVN16-2
0 active listings and RFQs →
EN 10083-2 C50E
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between EN 10088-1 X53CrSiMoVN16-2 and EN 10083-2 C50E?
Different category: EN 10088-1 X53CrSiMoVN16-2 is Stainless Steel, EN 10083-2 C50E is Carbon Steel. EN 10088-1 X53CrSiMoVN16-2 specifies V, N which are not specified for EN 10083-2 C50E. EN 10083-2 C50E specifies Cr+Mo+Ni which is not specified for EN 10088-1 X53CrSiMoVN16-2.
Can EN 10088-1 X53CrSiMoVN16-2 be substituted with EN 10083-2 C50E?
EN 10088-1 X53CrSiMoVN16-2 and EN 10083-2 C50E share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.