Post Stock Login Register

EN 10088-2 X2CrNbCu21 vs EN 10088-2 X2CrNbTi20

Close Alternative — 75.3% match based on chemical composition and mechanical property overlap.

EN 10088-2 X2CrNbCu21 (EN 10088-2:2014) and EN 10088-2 X2CrNbTi20 (EN 10088-2:2014) are both steel grades. Both fall under the Stainless Steel category. EN 10088-2 X2CrNbCu21 is typically used for general purposes, hot or cold rolled sheet/plate and strip, while EN 10088-2 X2CrNbTi20 is commonly used for general purposes, hot or cold rolled sheet/plate and strip. EN 10088-2 X2CrNbCu21 is defined under European Standard (EN), originating from Europe, while EN 10088-2 X2CrNbTi20 is defined under European Standard (EN), originating from Europe.

As per chemical composition, EN 10088-2 X2CrNbCu21 vs EN 10088-2 X2CrNbTi20 is a 84% match. As per mechanical properties, the match is 58%. Combined, this makes them a close alternative overall at 75.3%.

Frequently Compared With EN 10088-2 X2CrNbCu21:
ASTM A959 .- GOST 5632 08X18H10 EN 10088-1 1.4401 IS 1570 (Part 7) 12Cr12MoVH IS 1570 (Part 7) 12Cr13H GB/T 3280 06Cr19Ni10 GOST 5632 06Kh23N28 EN 10088-1 1.4006 EN 10088-1 1.4301 EN 10088-1 1.4845 IS 1570 (Part 7) 11Cr17Ni13W3TiH IS 1570 (Part 7) 12Cr12MoH
Match Breakdown
CHEMISTRY MATCH
84%
MECHANICAL MATCH
58%
OVERALL
75.3%
Specifications
Property EN 10088-2 X2CrNbCu21 EN 10088-2 X2CrNbTi20
Standard EN 10088-2:2014 EN 10088-2:2014
Category Stainless Steel Stainless Steel
C (%) <=0.030 <=0.030
Si (%) <=1.00 <=1.00
Mn (%) <=1.00 <=1.00
P (%) <=0.040 <=0.040
S (%) <=0.015 <=0.015
Cr (%) 20.0-21.5 18.5-20.5
N (%) <=0.030 <=0.030
Nb (%) 0.20-1.00 <=1.00
Cu (%) 0.10-1.00 Not specified
Ti (%) Not specified <=0.80
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property EN 10088-2 X2CrNbCu21 EN 10088-2 X2CrNbTi20
Tensile Strength 400-600 MPa 430-630 MPa
Condition Annealed (+A), cold rolled strip, up to 6 mm thick; Elongation is A80 (under 3 mm) or A (3 mm and over), longitudinal and transverse Annealed (+A), cold rolled strip, up to 8 mm thick; Elongation is A80 (under 3 mm) or A (3 mm and over), longitudinal and transverse
Yield Strength >=230 MPa >=230 MPa
Elongation >=22% >=18%
Typical Applications
EN 10088-2 X2CrNbCu21
General purposes, hot or cold rolled sheet/plate and strip
EN 10088-2 X2CrNbTi20
General purposes, hot or cold rolled sheet/plate and strip
Key Differences
Can EN 10088-2 X2CrNbCu21 Be Substituted With EN 10088-2 X2CrNbTi20?
EN 10088-2 X2CrNbCu21 and EN 10088-2 X2CrNbTi20 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.
On M-EX Right Now
EN 10088-2 X2CrNbCu21
0 active listings and RFQs →
EN 10088-2 X2CrNbTi20
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between EN 10088-2 X2CrNbCu21 and EN 10088-2 X2CrNbTi20?
EN 10088-2 X2CrNbCu21 specifies Cu which is not specified for EN 10088-2 X2CrNbTi20. EN 10088-2 X2CrNbTi20 specifies Ti which is not specified for EN 10088-2 X2CrNbCu21.
Can EN 10088-2 X2CrNbCu21 be substituted with EN 10088-2 X2CrNbTi20?
EN 10088-2 X2CrNbCu21 and EN 10088-2 X2CrNbTi20 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.