Post Stock Login Register

EN 10088-2 X2CrNiMnMoCuN24-4-3-2 vs EN 10088-2 X2CrNiMoN25-7-4

Related Material — 69.9% match based on chemical composition and mechanical property overlap.

EN 10088-2 X2CrNiMnMoCuN24-4-3-2 (EN 10088-2:2014) and EN 10088-2 X2CrNiMoN25-7-4 (EN 10088-2:2014) are both steel grades. Both fall under the Stainless Steel category. EN 10088-2 X2CrNiMnMoCuN24-4-3-2 is typically used for general purposes, hot or cold rolled sheet/plate and strip, while EN 10088-2 X2CrNiMoN25-7-4 is commonly used for general purposes, hot or cold rolled sheet/plate and strip. EN 10088-2 X2CrNiMnMoCuN24-4-3-2 is defined under European Standard (EN), originating from Europe, while EN 10088-2 X2CrNiMoN25-7-4 is defined under European Standard (EN), originating from Europe.

As per chemical composition, EN 10088-2 X2CrNiMnMoCuN24-4-3-2 vs EN 10088-2 X2CrNiMoN25-7-4 is a 62.6% match. As per mechanical properties, the match is 86.7%. Combined, this makes them a related material overall at 69.9%.

Frequently Compared With EN 10088-2 X2CrNiMnMoCuN24-4-3-2:
ASTM A959 .- GB/T 3280 06Cr19Ni10 GOST 5632 06Kh23N28 GOST 5632 08X18H10 EN 10088-1 1.4006 EN 10088-1 1.4301 EN 10088-1 1.4401 EN 10088-1 1.4845 IS 1570 (Part 7) 11Cr17Ni13W3TiH IS 1570 (Part 7) 12Cr12MoH IS 1570 (Part 7) 12Cr12MoVH IS 1570 (Part 7) 12Cr12Ni2Mo
Match Breakdown
CHEMISTRY MATCH
62.6%
MECHANICAL MATCH
86.7%
OVERALL
69.9%
Specifications
Property EN 10088-2 X2CrNiMnMoCuN24-4-3-2 EN 10088-2 X2CrNiMoN25-7-4
Standard EN 10088-2:2014 EN 10088-2:2014
Category Stainless Steel Stainless Steel
C (%) <=0.030 <=0.030
Si (%) <=0.70 <=1.00
Mn (%) 2.50-4.0 <=2.00
P (%) <=0.035 <=0.035
S (%) <=0.005 <=0.015
Cr (%) 23.0-25.0 24.0-26.0
Mo (%) 1.00-2.00 3.0-4.5
Ni (%) 3.0-4.5 6.0-8.0
N (%) 0.20-0.30 0.24-0.35
Cu (%) 0.10-0.80 Not specified
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property EN 10088-2 X2CrNiMnMoCuN24-4-3-2 EN 10088-2 X2CrNiMoN25-7-4
Tensile Strength 750-900 MPa 750-1000 MPa
Yield Strength >=550 MPa >=550 MPa
Elongation >=20% >=20%
Condition Solution annealed (+AT), cold rolled strip, up to 6.4 mm thick; Yield Strength is Rp0.2 (transverse), Elongation is A80 for under 3 mm thick Solution annealed (+AT), cold rolled strip, up to 8 mm thick; Yield Strength is Rp0.2 (transverse), Elongation is A80 for under 3 mm thick
Typical Applications
EN 10088-2 X2CrNiMnMoCuN24-4-3-2
General purposes, hot or cold rolled sheet/plate and strip
EN 10088-2 X2CrNiMoN25-7-4
General purposes, hot or cold rolled sheet/plate and strip
Key Differences
Can EN 10088-2 X2CrNiMnMoCuN24-4-3-2 Be Substituted With EN 10088-2 X2CrNiMoN25-7-4?
EN 10088-2 X2CrNiMnMoCuN24-4-3-2 and EN 10088-2 X2CrNiMoN25-7-4 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
On M-EX Right Now
EN 10088-2 X2CrNiMnMoCuN24-4-3-2
0 active listings and RFQs →
EN 10088-2 X2CrNiMoN25-7-4
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between EN 10088-2 X2CrNiMnMoCuN24-4-3-2 and EN 10088-2 X2CrNiMoN25-7-4?
EN 10088-2 X2CrNiMnMoCuN24-4-3-2 specifies Cu which is not specified for EN 10088-2 X2CrNiMoN25-7-4.
Can EN 10088-2 X2CrNiMnMoCuN24-4-3-2 be substituted with EN 10088-2 X2CrNiMoN25-7-4?
EN 10088-2 X2CrNiMnMoCuN24-4-3-2 and EN 10088-2 X2CrNiMoN25-7-4 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.