EN 10088-2 X2CrNiMoN18-12-4 vs IS 6603 X02Cr18Ni12Mo3N
Strong Match — 90.4% match
based on chemical composition and mechanical property overlap.
EN 10088-2 X2CrNiMoN18-12-4 (EN 10088-2:2014) and IS 6603 X02Cr18Ni12Mo3N (IS 6603:2024) are both steel grades.
Both fall under the Stainless Steel category.
EN 10088-2 X2CrNiMoN18-12-4 is typically used for general purposes, hot or cold rolled sheet/plate and strip, while IS 6603 X02Cr18Ni12Mo3N is commonly used for general purposes, semi-finished products, bars, wire rods and bright bars.
EN 10088-2 X2CrNiMoN18-12-4 is defined under European Standard (EN), originating from Europe, while IS 6603 X02Cr18Ni12Mo3N is defined under Bureau of Indian Standards (IS), originating from India.
As per chemical composition, EN 10088-2 X2CrNiMoN18-12-4 vs IS 6603 X02Cr18Ni12Mo3N is a 98.6% match.
As per mechanical properties, the match is 73.9%.
Combined, this makes them a strong match overall at 90.4%.
Frequently Compared With EN 10088-2 X2CrNiMoN18-12-4:
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property
EN 10088-2 X2CrNiMoN18-12-4
IS 6603 X02Cr18Ni12Mo3N
Tensile Strength
570-770 MPa
540-740 MPa
Yield Strength
>=290 MPa
Not specified
Elongation
>=35%
Not specified
Condition
Solution annealed (+AT), cold rolled strip, up to 8 mm thick; Yield Strength is Rp0.2 (transverse), Elongation is A80 for under 3 mm thick
Solution annealed, conditions 1C, 1E, 1D, 1X, 1G and 2D, rod only; Yield Strength is Rp0.2, Elongation is A (longitudinal)
Typical Applications
EN 10088-2 X2CrNiMoN18-12-4
General purposes, hot or cold rolled sheet/plate and strip
IS 6603 X02Cr18Ni12Mo3N
General purposes, semi-finished products, bars, wire rods and bright bars
Can EN 10088-2 X2CrNiMoN18-12-4 Be Substituted With IS 6603 X02Cr18Ni12Mo3N?
EN 10088-2 X2CrNiMoN18-12-4 and IS 6603 X02Cr18Ni12Mo3N overlap closely enough on chemistry and mechanical properties that IS 6603 X02Cr18Ni12Mo3N is often considered as a substitute for EN 10088-2 X2CrNiMoN18-12-4 in many applications. Always confirm the specific property range your application needs before substituting, and check with your supplier's mill certificate.
What is the difference between EN 10088-2 X2CrNiMoN18-12-4 and IS 6603 X02Cr18Ni12Mo3N?
Both grades share a similar composition profile; see the specification table above for the exact chemistry and mechanical property values.
Can EN 10088-2 X2CrNiMoN18-12-4 be substituted with IS 6603 X02Cr18Ni12Mo3N?
EN 10088-2 X2CrNiMoN18-12-4 and IS 6603 X02Cr18Ni12Mo3N overlap closely enough on chemistry and mechanical properties that IS 6603 X02Cr18Ni12Mo3N is often considered as a substitute for EN 10088-2 X2CrNiMoN18-12-4 in many applications. Always confirm the specific property range your application needs before substituting, and check with your supplier's mill certificate.