Post Stock Login Register

EN 10088-2 X5CrNiCu19-6-2 vs EN 10088-2 X5CrNi17-7

Close Alternative — 78.4% match based on chemical composition and mechanical property overlap.

EN 10088-2 X5CrNiCu19-6-2 (EN 10088-2:2014) and EN 10088-2 X5CrNi17-7 (EN 10088-2:2014) are both steel grades. Both fall under the Stainless Steel category. EN 10088-2 X5CrNiCu19-6-2 is typically used for general purposes, hot or cold rolled sheet/plate and strip, while EN 10088-2 X5CrNi17-7 is commonly used for general purposes, hot or cold rolled sheet/plate and strip. EN 10088-2 X5CrNiCu19-6-2 is defined under European Standard (EN), originating from Europe, while EN 10088-2 X5CrNi17-7 is defined under European Standard (EN), originating from Europe.

As per chemical composition, EN 10088-2 X5CrNiCu19-6-2 vs EN 10088-2 X5CrNi17-7 is a 68.3% match. As per mechanical properties, the match is 98.4%. Combined, this makes them a close alternative overall at 78.4%.

Frequently Compared With EN 10088-2 X5CrNiCu19-6-2:
ASTM A959 .- GB/T 3280 06Cr19Ni10 GOST 5632 06Kh23N28 GOST 5632 08X18H10 EN 10088-1 1.4006 EN 10088-1 1.4301 EN 10088-1 1.4401 EN 10088-1 1.4845 IS 1570 (Part 7) 11Cr17Ni13W3TiH IS 1570 (Part 7) 12Cr12MoH IS 1570 (Part 7) 12Cr12MoVH IS 1570 (Part 7) 12Cr12Ni2Mo
Match Breakdown
CHEMISTRY MATCH
68.3%
MECHANICAL MATCH
98.4%
OVERALL
78.4%
Specifications
Property EN 10088-2 X5CrNiCu19-6-2 EN 10088-2 X5CrNi17-7
Standard EN 10088-2:2014 EN 10088-2:2014
Category Stainless Steel Stainless Steel
C (%) 0.030-0.08 <=0.07
Si (%) <=0.50 <=1.00
Mn (%) 1.50-4.0 <=2.00
P (%) <=0.045 <=0.045
S (%) <=0.015 <=0.030
Cr (%) 18.0-19.0 16.0-18.0
Ni (%) 5.5-6.9 6.0-8.0
N (%) 0.03-0.11 <=0.10
Cu (%) 1.30-2.00 Not specified
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property EN 10088-2 X5CrNiCu19-6-2 EN 10088-2 X5CrNi17-7
Tensile Strength 540-750 MPa 550-750 MPa
Yield Strength >=230 MPa >=230 MPa
Elongation >=45% >=45%
Condition Solution annealed (+AT), cold rolled strip, up to 8 mm thick; Yield Strength is Rp0.2 (transverse), Elongation is A80 for under 3 mm thick Solution annealed (+AT), cold rolled strip, up to 3 mm thick; Yield Strength is Rp0.2 (transverse), Elongation is A80 for under 3 mm thick
Typical Applications
EN 10088-2 X5CrNiCu19-6-2
General purposes, hot or cold rolled sheet/plate and strip
EN 10088-2 X5CrNi17-7
General purposes, hot or cold rolled sheet/plate and strip
Key Differences
Can EN 10088-2 X5CrNiCu19-6-2 Be Substituted With EN 10088-2 X5CrNi17-7?
EN 10088-2 X5CrNiCu19-6-2 and EN 10088-2 X5CrNi17-7 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.
On M-EX Right Now
EN 10088-2 X5CrNiCu19-6-2
0 active listings and RFQs →
EN 10088-2 X5CrNi17-7
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between EN 10088-2 X5CrNiCu19-6-2 and EN 10088-2 X5CrNi17-7?
EN 10088-2 X5CrNiCu19-6-2 specifies Cu which is not specified for EN 10088-2 X5CrNi17-7.
Can EN 10088-2 X5CrNiCu19-6-2 be substituted with EN 10088-2 X5CrNi17-7?
EN 10088-2 X5CrNiCu19-6-2 and EN 10088-2 X5CrNi17-7 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.