Post Stock Login Register

EN 10088-2 X5CrNiN19-9 vs BS 970 (Part 3) 304S15

Strong Match — 88.1% match based on chemical composition and mechanical property overlap.

EN 10088-2 X5CrNiN19-9 (EN 10088-2:2014) and BS 970 (Part 3) 304S15 (BS 970 (Part 3):1991) are both steel grades. Both fall under the Stainless Steel category. EN 10088-2 X5CrNiN19-9 is typically used for general purposes, hot or cold rolled sheet/plate and strip, while BS 970 (Part 3) 304S15 is commonly used for bright cold finished bars (cold drawn, turned or precision ground) for general engineering purposes, in straight lengths; austenitic stainless and heat resisting steel (table 18). EN 10088-2 X5CrNiN19-9 is defined under European Standard (EN), originating from Europe, while BS 970 (Part 3) 304S15 is defined under British Standards (BS), originating from United Kingdom.

As per chemical composition, EN 10088-2 X5CrNiN19-9 vs BS 970 (Part 3) 304S15 is a 88.1% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a strong match overall at 88.1%.

Frequently Compared With EN 10088-2 X5CrNiN19-9:
EN 10088-1 1.4006 ASTM A959 .- GB/T 3280 06Cr19Ni10 EN 10088-1 1.4301 EN 10088-1 1.4401 EN 10088-1 1.4845 IS 1570 (Part 7) 12Cr12Ni2Mo IS 1570 (Part 7) 12Cr13H GOST 5632 06Kh23N28 GOST 5632 08X18H10 IS 1570 (Part 7) 11Cr17Ni13W3TiH IS 1570 (Part 7) 12Cr12MoH
Match Breakdown
CHEMISTRY MATCH
88.1%
MECHANICAL MATCH
No shared data
OVERALL
88.1%
Specifications
Property EN 10088-2 X5CrNiN19-9 BS 970 (Part 3) 304S15
Standard EN 10088-2:2014 BS 970 (Part 3):1991
Category Stainless Steel Stainless Steel
C (%) <=0.06 <=0.06
Si (%) <=1.00 <=1.0
Mn (%) <=2.00 <=2.0
P (%) <=0.045 <=0.045
S (%) <=0.015 <=0.030
Cr (%) 18.0-20.0 17.5-19.0
Ni (%) 8.0-11.0 8.0-11.0
N (%) 0.12-0.22 Not specified
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property EN 10088-2 X5CrNiN19-9 BS 970 (Part 3) 304S15
Tensile Strength 500-750 MPa Not specified
Yield Strength >=290 MPa Not specified
Elongation >=40% Not specified
Condition Solution annealed (+AT), cold rolled strip, up to 8 mm thick; Yield Strength is Rp0.2 (transverse), Elongation is A80 for under 3 mm thick Not specified
Typical Applications
EN 10088-2 X5CrNiN19-9
General purposes, hot or cold rolled sheet/plate and strip
BS 970 (Part 3) 304S15
Bright cold finished bars (cold drawn, turned or precision ground) for general engineering purposes, in straight lengths; austenitic stainless and heat resisting steel (Table 18)
Key Differences
Can EN 10088-2 X5CrNiN19-9 Be Substituted With BS 970 (Part 3) 304S15?
EN 10088-2 X5CrNiN19-9 and BS 970 (Part 3) 304S15 overlap closely enough on chemistry and mechanical properties that BS 970 (Part 3) 304S15 is often considered as a substitute for EN 10088-2 X5CrNiN19-9 in many applications. Always confirm the specific property range your application needs before substituting, and check with your supplier's mill certificate.
On M-EX Right Now
EN 10088-2 X5CrNiN19-9
0 active listings and RFQs →
BS 970 (Part 3) 304S15
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between EN 10088-2 X5CrNiN19-9 and BS 970 (Part 3) 304S15?
EN 10088-2 X5CrNiN19-9 specifies N which is not specified for BS 970 (Part 3) 304S15.
Can EN 10088-2 X5CrNiN19-9 be substituted with BS 970 (Part 3) 304S15?
EN 10088-2 X5CrNiN19-9 and BS 970 (Part 3) 304S15 overlap closely enough on chemistry and mechanical properties that BS 970 (Part 3) 304S15 is often considered as a substitute for EN 10088-2 X5CrNiN19-9 in many applications. Always confirm the specific property range your application needs before substituting, and check with your supplier's mill certificate.