Post Stock Login Register

EN 10088-2 X6CrNiNb18-10 vs IS 1570 (Part 7) 11Cr17Ni13W3TiH

Minimal Match — 42.3% match based on chemical composition and mechanical property overlap.

EN 10088-2 X6CrNiNb18-10 (EN 10088-2:2014) and IS 1570 (Part 7) 11Cr17Ni13W3TiH (IS 1570 (Part 7):1992) are both steel grades. Both fall under the Stainless Steel category. EN 10088-2 X6CrNiNb18-10 is typically used for general purposes, hot or cold rolled sheet/plate and strip, while IS 1570 (Part 7) 11Cr17Ni13W3TiH is commonly used for boilers, pressure vessels, steam turbines, steam and water piping and other power plant equipment working at elevated temperature. EN 10088-2 X6CrNiNb18-10 is defined under European Standard (EN), originating from Europe, while IS 1570 (Part 7) 11Cr17Ni13W3TiH is defined under Bureau of Indian Standards (IS), originating from India.

As per chemical composition, EN 10088-2 X6CrNiNb18-10 vs IS 1570 (Part 7) 11Cr17Ni13W3TiH is a 56.3% match. As per mechanical properties, the match is 14.3%. Combined, this makes them a minimal match overall at 42.3%.

Frequently Compared With EN 10088-2 X6CrNiNb18-10:
EN 10088-1 1.4401 EN 10088-1 1.4006 ASTM A959 .- GB/T 3280 06Cr19Ni10 GOST 5632 06Kh23N28 GOST 5632 08X18H10 EN 10088-1 1.4301 IS 1570 (Part 7) 12Cr12MoH IS 1570 (Part 7) 12Cr12MoVH IS 1570 (Part 7) 12Cr12Ni2Mo IS 1570 (Part 7) 12Cr13H EN 10088-1 1.4845
Match Breakdown
CHEMISTRY MATCH
56.3%
MECHANICAL MATCH
14.3%
OVERALL
42.3%
Specifications
Property EN 10088-2 X6CrNiNb18-10 IS 1570 (Part 7) 11Cr17Ni13W3TiH
Standard EN 10088-2:2014 IS 1570 (Part 7):1992
Category Stainless Steel Stainless Steel
C (%) <=0.08 0.07-0.15
Si (%) <=1.00 <=1.00
Mn (%) <=2.00 <=1.00
P (%) <=0.045 <=0.045
S (%) <=0.015 <=0.030
Cr (%) 17.0-19.0 15.5-17.50
Ni (%) 9.0-12.0 12.00-14.50
Nb (%) <=1.00 Not specified
W (%) Not specified 2.5-3.5
Ti (%) Not specified >=4xC, <=0.80
B (%) Not specified <=0.0006
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property EN 10088-2 X6CrNiNb18-10 IS 1570 (Part 7) 11Cr17Ni13W3TiH
Tensile Strength 520-720 MPa 600-800 MPa
Yield Strength >=220 MPa >=390 MPa (0.2 % proof stress)
Elongation >=40% >=25%
Condition Solution annealed (+AT), cold rolled strip, up to 8 mm thick; Yield Strength is Rp0.2 (transverse), Elongation is A80 for under 3 mm thick Bars, forgings, pipes, hot cold worked, thickness up to 60 (first row of Table 3)
Typical Applications
EN 10088-2 X6CrNiNb18-10
General purposes, hot or cold rolled sheet/plate and strip
IS 1570 (Part 7) 11Cr17Ni13W3TiH
Boilers, pressure vessels, steam turbines, steam and water piping and other power plant equipment working at elevated temperature
Key Differences
Can EN 10088-2 X6CrNiNb18-10 Be Substituted With IS 1570 (Part 7) 11Cr17Ni13W3TiH?
EN 10088-2 X6CrNiNb18-10 and IS 1570 (Part 7) 11Cr17Ni13W3TiH share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
On M-EX Right Now
EN 10088-2 X6CrNiNb18-10
0 active listings and RFQs →
IS 1570 (Part 7) 11Cr17Ni13W3TiH
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between EN 10088-2 X6CrNiNb18-10 and IS 1570 (Part 7) 11Cr17Ni13W3TiH?
EN 10088-2 X6CrNiNb18-10 specifies Nb which is not specified for IS 1570 (Part 7) 11Cr17Ni13W3TiH. IS 1570 (Part 7) 11Cr17Ni13W3TiH specifies W, Ti, B which are not specified for EN 10088-2 X6CrNiNb18-10.
Can EN 10088-2 X6CrNiNb18-10 be substituted with IS 1570 (Part 7) 11Cr17Ni13W3TiH?
EN 10088-2 X6CrNiNb18-10 and IS 1570 (Part 7) 11Cr17Ni13W3TiH share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.