Post Stock Login Register

EN 10088-2 X6CrNiTi12 vs BS 970 (Part 1) 403S17

Close Alternative — 74.1% match based on chemical composition and mechanical property overlap.

EN 10088-2 X6CrNiTi12 (EN 10088-2:2014) and BS 970 (Part 1) 403S17 (BS 970 (Part 1):1983) are both steel grades. Both fall under the Stainless Steel category. EN 10088-2 X6CrNiTi12 is typically used for general purposes, hot or cold rolled sheet/plate and strip, while BS 970 (Part 1) 403S17 is commonly used for stainless and heat resisting steel for mechanical and allied engineering purposes (table 13).. EN 10088-2 X6CrNiTi12 is defined under European Standard (EN), originating from Europe, while BS 970 (Part 1) 403S17 is defined under British Standards (BS), originating from United Kingdom.

As per chemical composition, EN 10088-2 X6CrNiTi12 vs BS 970 (Part 1) 403S17 is a 74.1% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a close alternative overall at 74.1%.

Frequently Compared With EN 10088-2 X6CrNiTi12:
ASTM A959 .- GB/T 3280 06Cr19Ni10 GOST 5632 06Kh23N28 GOST 5632 08X18H10 EN 10088-1 1.4006 EN 10088-1 1.4301 EN 10088-1 1.4401 EN 10088-1 1.4845 IS 1570 (Part 7) 11Cr17Ni13W3TiH IS 1570 (Part 7) 12Cr12MoH IS 1570 (Part 7) 12Cr12MoVH IS 1570 (Part 7) 12Cr12Ni2Mo
Match Breakdown
CHEMISTRY MATCH
74.1%
MECHANICAL MATCH
No shared data
OVERALL
74.1%
Specifications
Property EN 10088-2 X6CrNiTi12 BS 970 (Part 1) 403S17
Standard EN 10088-2:2014 BS 970 (Part 1):1983
Category Stainless Steel Stainless Steel
C (%) <=0.08 <=0.08
Si (%) <=0.70 <=1.0
Mn (%) <=1.50 <=1.0
P (%) <=0.040 <=0.040
S (%) <=0.015 <=0.030
Cr (%) 10.5-12.5 12.0-14.0
Ni (%) 0.50-1.50 <=0.50
Ti (%) 0.05-0.35 Not specified
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property EN 10088-2 X6CrNiTi12 BS 970 (Part 1) 403S17
Tensile Strength 450-650 MPa Not specified
Condition Annealed (+A), cold rolled strip, up to 8 mm thick; Elongation is A80 (under 3 mm) or A (3 mm and over), longitudinal and transverse Not specified
Yield Strength >=280 MPa Not specified
Elongation >=23% Not specified
Typical Applications
EN 10088-2 X6CrNiTi12
General purposes, hot or cold rolled sheet/plate and strip
BS 970 (Part 1) 403S17
Stainless and heat resisting steel for mechanical and allied engineering purposes (Table 13).
Key Differences
Can EN 10088-2 X6CrNiTi12 Be Substituted With BS 970 (Part 1) 403S17?
EN 10088-2 X6CrNiTi12 and BS 970 (Part 1) 403S17 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.
On M-EX Right Now
EN 10088-2 X6CrNiTi12
0 active listings and RFQs →
BS 970 (Part 1) 403S17
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between EN 10088-2 X6CrNiTi12 and BS 970 (Part 1) 403S17?
EN 10088-2 X6CrNiTi12 specifies Ti which is not specified for BS 970 (Part 1) 403S17.
Can EN 10088-2 X6CrNiTi12 be substituted with BS 970 (Part 1) 403S17?
EN 10088-2 X6CrNiTi12 and BS 970 (Part 1) 403S17 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.