Post Stock Login Register

EN 10088-3 X12CrMnNiN17-7-5 vs EN 10088-1 1.4006

Minimal Match — 35% match based on chemical composition and mechanical property overlap.

EN 10088-3 X12CrMnNiN17-7-5 (EN 10088-3:2014) and EN 10088-1 1.4006 (EN 10088-1:2014) are both steel grades. Both fall under the Stainless Steel category. EN 10088-3 X12CrMnNiN17-7-5 is typically used for general purposes, semi-finished products, bars, rods, wire, sections and bright products, while EN 10088-1 1.4006 is commonly used for cutlery, turbine blades, fasteners, surgical instruments. EN 10088-3 X12CrMnNiN17-7-5 is defined under European Standard (EN), originating from Europe, while EN 10088-1 1.4006 is defined under European Standard (EN), originating from Europe.

As per chemical composition, EN 10088-3 X12CrMnNiN17-7-5 vs EN 10088-1 1.4006 is a 60.3% match. As per mechanical properties, the match is 0%. Combined, this makes them a minimal match overall at 35%.

Frequently Compared With EN 10088-3 X12CrMnNiN17-7-5:
ASTM A959 201 ASTM A959 .- GB/T 3280 06Cr19Ni10 EN 10088-1 1.4301 EN 10088-1 1.4401 EN 10088-1 1.4845 IS 1570 (Part 7) 11Cr17Ni13W3TiH ASTM A959 202 GOST 5632 06Kh23N28 GOST 5632 08X18H10 IS 1570 (Part 7) 12Cr12MoH IS 1570 (Part 7) 12Cr12MoVH
Match Breakdown
CHEMISTRY MATCH
60.3%
MECHANICAL MATCH
0%
OVERALL
35%
Specifications
Property EN 10088-3 X12CrMnNiN17-7-5 EN 10088-1 1.4006
Standard EN 10088-3:2014 EN 10088-1:2014
Category Stainless Steel Stainless Steel
C (%) <=0.15 0.08–0.15
Si (%) <=1.00 ≤1.00
Mn (%) 5.5-7.5 ≤1.50
P (%) <=0.045 Not specified
S (%) <=0.015 Not specified
Cr (%) 16.0-18.0 11.5–13.5
Ni (%) 3.5-5.5 ≤0.75
N (%) 0.05-0.25 Not specified
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property EN 10088-3 X12CrMnNiN17-7-5 EN 10088-1 1.4006
Tensile Strength 680-880 MPa ≥540 MPa (annealed)
Yield Strength >=230 MPa Not specified
Elongation >=40% ≥18%
Hardness <=260 HB Not specified
Condition Solution annealed (+AT), conditions 1C, 1E, 1D, 1X, 1G and 2D, thickness or diameter up to 160 mm; Yield Strength is Rp0.2, Elongation is A (longitudinal), hardness for guidance only Not specified
Hardness HRC Not specified 36–45 (hardened)
Typical Applications
EN 10088-3 X12CrMnNiN17-7-5
General purposes, semi-finished products, bars, rods, wire, sections and bright products
EN 10088-1 1.4006
Cutlery, turbine blades, fasteners, surgical instruments
Key Differences
Can EN 10088-3 X12CrMnNiN17-7-5 Be Substituted With EN 10088-1 1.4006?
EN 10088-3 X12CrMnNiN17-7-5 and EN 10088-1 1.4006 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
Forms & Sizes Available on M-EX
EN 10088-3 X12CrMnNiN17-7-5
No active listings currently.
EN 10088-1 1.4006
Sheet → (3 listings)
Thickness: 6–6 mm (0.24–0.24 in)
Width: 1250–1250 mm (49.21–49.21 in)
Length: 2700–3400 mm (106.3–133.86 in)
On M-EX Right Now
EN 10088-3 X12CrMnNiN17-7-5
0 active listings and RFQs →
EN 10088-1 1.4006
3 active listings and RFQs →
Frequently Asked Questions
What is the difference between EN 10088-3 X12CrMnNiN17-7-5 and EN 10088-1 1.4006?
EN 10088-3 X12CrMnNiN17-7-5 specifies P, S, N which are not specified for EN 10088-1 1.4006.
Can EN 10088-3 X12CrMnNiN17-7-5 be substituted with EN 10088-1 1.4006?
EN 10088-3 X12CrMnNiN17-7-5 and EN 10088-1 1.4006 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.