Post Stock Login Register

EN 10088-3 X1CrNiMoAlTi12-9-2 vs ASTM A959 S46500

Related Material — 61.2% match based on chemical composition and mechanical property overlap.

EN 10088-3 X1CrNiMoAlTi12-9-2 (EN 10088-3:2014) and ASTM A959 S46500 (ASTM A959:2011) are both steel grades. Both fall under the Stainless Steel category. EN 10088-3 X1CrNiMoAlTi12-9-2 is typically used for general purposes, semi-finished products, bars, rods, wire, sections and bright products, while ASTM A959 S46500 is commonly used for wrought stainless steel products; recommended composition limits for adoption by product standards (clause 1.1). EN 10088-3 X1CrNiMoAlTi12-9-2 is defined under European Standard (EN), originating from Europe, while ASTM A959 S46500 is defined under ASTM International, originating from United States.

As per chemical composition, EN 10088-3 X1CrNiMoAlTi12-9-2 vs ASTM A959 S46500 is a 61.2% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a related material overall at 61.2%.

Frequently Compared With EN 10088-3 X1CrNiMoAlTi12-9-2:
EN 10088-1 1.4006 IS 1570 (Part 7) 12Cr12MoH ASTM A959 .- GB/T 3280 06Cr19Ni10 GOST 5632 06Kh23N28 GOST 5632 08X18H10 EN 10088-1 1.4301 EN 10088-1 1.4401 EN 10088-1 1.4845 IS 1570 (Part 7) 11Cr17Ni13W3TiH IS 1570 (Part 7) 12Cr12MoVH IS 1570 (Part 7) 12Cr12Ni2Mo
Match Breakdown
CHEMISTRY MATCH
61.2%
MECHANICAL MATCH
No shared data
OVERALL
61.2%
Specifications
Property EN 10088-3 X1CrNiMoAlTi12-9-2 ASTM A959 S46500
Standard EN 10088-3:2014 ASTM A959:2011
Category Stainless Steel Stainless Steel
C (%) <=0.015 <=0.020
Si (%) <=0.10 <=0.25
Mn (%) <=0.10 <=0.25
P (%) <=0.010 <=0.015
S (%) <=0.005 <=0.010
Cr (%) 11.5-12.5 11.0-12.5
Mo (%) 1.85-2.15 0.75-1.25
Ni (%) 8.5-9.5 10.7-11.3
Al (%) 0.60-0.80 Not specified
Ti (%) 0.28-0.37 1.50-1.80
N (%) <=0.010 <=0.010
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property EN 10088-3 X1CrNiMoAlTi12-9-2 ASTM A959 S46500
Tensile Strength <=1200 MPa Not specified
Hardness <=363 HB Not specified
Condition Solution annealed (+AT), conditions 1C, 1E, 1D, 1X, 1G and 2D, thickness or diameter up to 150 mm; hardness for guidance only Not specified
Typical Applications
EN 10088-3 X1CrNiMoAlTi12-9-2
General purposes, semi-finished products, bars, rods, wire, sections and bright products
ASTM A959 S46500
Wrought stainless steel products; recommended composition limits for adoption by product standards (clause 1.1)
Key Differences
Can EN 10088-3 X1CrNiMoAlTi12-9-2 Be Substituted With ASTM A959 S46500?
EN 10088-3 X1CrNiMoAlTi12-9-2 and ASTM A959 S46500 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
On M-EX Right Now
EN 10088-3 X1CrNiMoAlTi12-9-2
0 active listings and RFQs →
ASTM A959 S46500
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between EN 10088-3 X1CrNiMoAlTi12-9-2 and ASTM A959 S46500?
EN 10088-3 X1CrNiMoAlTi12-9-2 specifies Al which is not specified for ASTM A959 S46500.
Can EN 10088-3 X1CrNiMoAlTi12-9-2 be substituted with ASTM A959 S46500?
EN 10088-3 X1CrNiMoAlTi12-9-2 and ASTM A959 S46500 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.