Post Stock Login Register

EN 10088-3 X1CrNiMoCuN24-22-8 vs EN 10088-1 X1CrNiMoCuNW24-22-6

Related Material — 69.9% match based on chemical composition and mechanical property overlap.

EN 10088-3 X1CrNiMoCuN24-22-8 (EN 10088-3:2014) and EN 10088-1 X1CrNiMoCuNW24-22-6 (EN 10088-1:2014) are both steel grades. Both fall under the Stainless Steel category. EN 10088-3 X1CrNiMoCuN24-22-8 is defined under European Standard (EN), originating from Europe, while EN 10088-1 X1CrNiMoCuNW24-22-6 is defined under European Standard (EN), originating from Europe.

As per chemical composition, EN 10088-3 X1CrNiMoCuN24-22-8 vs EN 10088-1 X1CrNiMoCuNW24-22-6 is a 76.2% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a related material overall at 69.9%.

Frequently Compared With EN 10088-3 X1CrNiMoCuN24-22-8:
ASTM A959 .- GB/T 3280 06Cr19Ni10 GOST 5632 06Kh23N28 GOST 5632 08X18H10 EN 10088-1 1.4006 EN 10088-1 1.4301 EN 10088-1 1.4401 EN 10088-1 1.4845 IS 1570 (Part 7) 11Cr17Ni13W3TiH IS 1570 (Part 7) 12Cr12MoH IS 1570 (Part 7) 12Cr12MoVH IS 1570 (Part 7) 12Cr12Ni2Mo
Match Breakdown
CHEMISTRY MATCH
76.2%
MECHANICAL MATCH
No shared data
OVERALL
69.9%
Specifications
Property EN 10088-3 X1CrNiMoCuN24-22-8 EN 10088-1 X1CrNiMoCuNW24-22-6
Standard EN 10088-3:2014 EN 10088-1:2014
Category Stainless Steel Stainless Steel
C (%) <=0.020 <=0.020
Si (%) <=0.50 <=0.70
Mn (%) 2.00-4.0 2.00-4.0
P (%) <=0.030 <=0.030
S (%) <=0.005 <=0.010
Cr (%) 23.0-25.0 23.0-25.0
Mo (%) 7.0-8.0 5.5-6.5
Ni (%) 21.0-23.0 21.0-23.0
N (%) 0.45-0.55 0.35-0.50
Cu (%) 0.30-0.60 1.00-2.00
W (%) Not specified 1.50-2.50
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property EN 10088-3 X1CrNiMoCuN24-22-8 EN 10088-1 X1CrNiMoCuNW24-22-6
Tensile Strength 750-1000 MPa Not specified
Yield Strength >=430 MPa Not specified
Elongation >=40% Not specified
Hardness <=310 HB Not specified
Condition Solution annealed (+AT), conditions 1C, 1E, 1D, 1X, 1G and 2D, thickness or diameter up to 50 mm; Yield Strength is Rp0.2, Elongation is A (longitudinal), hardness for guidance only Not specified
Typical Applications
EN 10088-3 X1CrNiMoCuN24-22-8
General purposes, semi-finished products, bars, rods, wire, sections and bright products
EN 10088-1 X1CrNiMoCuNW24-22-6
Not documented
Key Differences
Can EN 10088-3 X1CrNiMoCuN24-22-8 Be Substituted With EN 10088-1 X1CrNiMoCuNW24-22-6?
EN 10088-3 X1CrNiMoCuN24-22-8 and EN 10088-1 X1CrNiMoCuNW24-22-6 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
On M-EX Right Now
EN 10088-3 X1CrNiMoCuN24-22-8
0 active listings and RFQs →
EN 10088-1 X1CrNiMoCuNW24-22-6
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between EN 10088-3 X1CrNiMoCuN24-22-8 and EN 10088-1 X1CrNiMoCuNW24-22-6?
EN 10088-1 X1CrNiMoCuNW24-22-6 specifies W which is not specified for EN 10088-3 X1CrNiMoCuN24-22-8.
Can EN 10088-3 X1CrNiMoCuN24-22-8 be substituted with EN 10088-1 X1CrNiMoCuNW24-22-6?
EN 10088-3 X1CrNiMoCuN24-22-8 and EN 10088-1 X1CrNiMoCuNW24-22-6 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.